648500
4
Zoom out
Zoom in
Previous page
1/56
Next page
SPECIFICATIONS
Club WS1000 Club WS1200
10" (250mm) 12" (300mm)
Low-profile SSI Automotive Subwoofer Low-profile SSI Automotive Subwoofer
Power Handling (RMS): 200W 250W
Power Handling (Peak): 800W 1000W
Sensitivity
@ 2.83V/1m: 89dB 92dB
Frequency Response: 35Hz – 175Hz 27Hz – 175Hz
Impedance: 2 or 4 ohms (selectable) 2 or 4 ohms (selectable)
Voice-Coil Diameter: 2" (50mm) 2" (50mm)
Mounting Depth: 3-5/16" (83mm) 3-5/16" (83mm)
Overall Diameter: 10-9/16" (268mm) 12-1/4" (310mm)
Cutout Diameter: 9-1/2" (240mm) 11-1/8" (282mm)
A valid serial number is required for warranty coverage.
Features, specifications and appearance are subject to change without notice.
These products are designed for mobile applications and are not intended for connection to the mains.
HARMAN International Industries, Inc. 8500 Balboa Boulevard, Northridge, CA 91329 USA
www.jbl.com
© 2015 HARMAN International Industries, Incorporated. All rights reserved.
JBL is a trademark of HARMAN International Industries, Incorporated registered in the United States and/or other countries.
2-Ohm Setting
MOUNTING THE
SUBWOOFER
The Club WS1000 and WS1200 subwoofers
can be mounted from the outside of the
enclosure or from the inside of the
enclosure. Which- ever way you mount the
subwoofer, use the included foam
mounting gasket to ensure a leak-free
seal between the subwoofer frame and
the enclosure.
CONNECTING THE
SUBWOOFER
SETTING THE IMPEDANCE
The Club WS1000 and WS1200 subwoofers
both feature the Selectable Smart
Impedance
(SSI) switch. This exclusive
feature lets you set the subwoofer’s
impedance to either 2 ohms or 4 ohms
with the flip of a switch (see illustrations
to the right). This allows you to extract
the most from your subwoofer amplifier in
any situation.
The SSI 2-ohm setting increases the
subwoofer’s output over the 4-ohm
setting by up to 3dB, depending on the
amplifier. Performance is identical in all
4-Ohm Setting
other respects. If the connected amplifier
is rated for 2-ohm operation and its 2-ohm
power ratings are within the subwoofer’s
power-handling specifications, setting
the SSI switch in the 2-ohm position will
achieve maximum output.
IMPORTANT: Make sure the
subwoofer amplifier is turned OFF before
setting the SSI switch. Do not change the
switch position while the subwoofer
amplifier is operating. Doing so could
damage the amplifier.
CONNECTING THE AMPLIFIER
The Club WS1000 and WS1200 subwoofer
connectors are compatible with quick-
disconnect (not supplied) or soldered
connections. The recommended wire gauge
is between 14AWG and 8AWG, depending
on the length of the wire run between the
amplifier and woofer. Heavier gauge wire
is preferred for runs over 6' (2m).
The wider terminal is the positive and the
narrower is negative (also indicated on
the terminal cover).
NOTE: If using untinned bare wire, be
sure that no stray “+” and “–” strands
touch each other. Touching strands can
cause a short circuit, which can damage
your amplifier.
CLUB SUBWOOFERS
WS1000 and WS1200
EN
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Club WS1200 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Club WS1200 in the language / languages: All languages as an attachment in your email.

The manual is 3,53 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info