809540
2
Zoom out
Zoom in
Previous page
1/8
Next page
2
On/Standby LED: When the Power-On Mode Switch is in the “Auto”
position, this LED indicates whether the subwoofer is in the On or
Standby state:
When the LED glows green, the subwoofer is turned on.
• When the LED glows red, the subwoofer is in the Standby mode.
When the Power Switch is set to “Off,” the LED will not light up, no
matter what setting the Power-On Mode Switch is in.
Crossover Control: This control determines the highest frequency
at which the subwoofer reproduces sounds. The higher you set the
Crossover Control, the higher in frequency the subwoofer will operate
and the more its bass will “overlap” that of the satellite speakers. This
adjustment helps achieve a smooth transition of bass frequencies
between the subwoofer and the satellites for a variety of different
rooms and subwoofer locations.
NOTE: The Crossover Control functions only when you are using
the Line-Level In L/R Connectors. The Line-Level In LFE Connector
bypasses the subwoofer’s built-in crossover and Crossover Control.
Phase Switch: This switch determines whether the subwoofer
driver’s piston-like action moves in and out in phase with the satellite
speakers. If the subwoofer were to play out of phase with the satellite
speakers, the sound waves from the satellites could partially cancel
out the sound waves from the subwoofer, reducing bass performance
and sonic impact. This phenomenon depends in part on the placement
of all the speakers relative to each other in the room.
Power-On Mode Switch: When this switch is set in the “Auto”
position and the Power Switch is set to “On,” the subwoofer will
automatically turn itself on when it receives an audio signal and will
enter the Standby mode when it has gone without receiving an audio
signal for 20 minutes. When this switch is set in the “On” position, the
subwoofer will remain on whether or not it is receiving an audio signal.
Subwoofer Level Control: Use this control to adjust the subwoofer’s
volume. Turn the knob clockwise to increase the volume; turn the knob
counterclockwise to decrease the volume.
Line-Level In LFE Connector: This input bypasses the subwoofer’s
internal crossover circuitry, so use it only with a receiver or processor
subwoofer output that has been low-pass filtered. If your receiver or
processor does not have a dedicated subwoofer output that is low-
pass filtered, use the subwoofer’s Line-Level In L/R Connectors (see
below) instead.
Use the supplied mono RCA cable (purple connectors) to connect the
Line-Level In LFE Connector to the dedicated subwoofer output of a
receiver or preamp/processor.
Line-Level In L/R Connectors: These inputs pass through the
subwoofer’s built-in crossover. Use them if your receiver or preamp/
processor does not have a dedicated subwoofer output that is low-
pass filtered.
Power Switch: Set this switch in the “On” position to turn the
subwoofer on. The subwoofer will then be in On or Standby mode,
depending on the setting of the Power-On Mode Switch.
Power Cord: After you have made and verified all subwoofer and
speaker connections described in this manual, plug the power cord
into an active, unswitched electrical outlet for proper operation of the
subwoofer. DO NOT plug this cord into the accessory outlets found on
some audio components.
SUBWOOFER REAR-PANEL CONTROLS AND CONNECTIONS
This Class B digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe B est conforme à la norme
NMB-003 du Canada.
Subwoofer
Level Control
Crossover
Control
On/Standby
LED
Phase Switch
Power-On
Mode Switch
Line-Level In
LFE Connector
Line-Level In
L/R Connectors
Power Switch
Power Cord
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Cinesystem 500 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Cinesystem 500 in the language / languages: English as an attachment in your email.

The manual is 1.58 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info