648472
7
Zoom out
Zoom in
Previous page
1/12
Next page
7
www.jbl.com
English
POWER CONNECTIONS
After verifying that all of the source connections have been made
properly, plug the supplied power cords into the soundbar’s and
subwoofer’s Power Cord connectors, and plug the other ends into
active, unswitched AC outlets. Do NOT plug this cords into the
accessory outlet found on some audio components.
To
Unswitched
AC Outlet
Power
Cord
(supplied)
Power
Cord
(supplied)
To
Unswitched
AC Outlet
USING YOUR SOUNDBAR SYSTEM
TURNING THE SOUNDBAR ON AND OFF
Press the Power button on either the soundbar or the remote
control to turn the soundbar on. To put the soundbar in the Standby
mode, press either Power button while the soundbar is on.
If you have manually put the soundbar into the Standby mode by
pressing the Power button, you can turn it back on by:
1. Pressing the Power button again
2. Streaming music from a connected Bluetooth device
The soundbar will automatically go into the Standby mode after 10
minutes of inactivity. If the soundbar has automatically gone into
the Standby mode, it will automatically turn itself on again when it
receives an audio signal from the last detected connection.
NOTE: You can control the soundbar with your own TV
remote control. See the “Using Your Own TV Remote (TV
Remote Learning)” section for more information.
TURNING THE SUBWOOFER ON AND OFF
Set the subwoofer’s Power switch to the “On” position. Once
the subwoofer and soundbar have been paired (see Pairing the
Units for Wireless Operation, below) the subwoofer will turn on
when the soundbar turns on and will remain on for approximately
30 seconds after the soundbar enters the Standby mode, or
for approximately 10 minutes after the audio signal ceases. If
you will be away from home for an extended period of time, or if
you will not be using the system for an extended period, set the
subwoofer’s Power switch to the “Off” position.
Pairing the Units for Wireless Operation
The JBL Cinema SB450 soundbar and wireless subwoofer are
automatically “paired” with each other. If the system does not
connect right away, press the Wireless Pairing buttons on both
units within 30 seconds of each other. The units will communicate
with each other and operate at the same frequency.
Soundbar
Pairing Switch
Subwoofer
Pairing Switch
NOTE: The maximum wireless operating distance
between the soundbar and subwoofer is approximately
30 feet (10m).
SWITCHING SOURCES
You may select any of the devices that are connected to the
soundbar by pressing the corresponding button on the JBL
Cinema SB450 remote control or pressing the source button on
the top button panel. The active source’s Source Indicator LED will
illuminate.
If you have connected devices directly to your TV’s input
connections AND you have connected the soundbar to your TV’s
HDMI ARC input, then audio will flow from the TV to the soundbar.
1. Press the HDMI TV button on the JBL SB450 remote control
to select audio from your TV.
2. Use your TV remote control to select the corresponding input
source device—this may be with an “INPUT” or “SOURCE”
button. Refer to your TV settings and operation.
ADJUSTING THE SYSTEM’S VOLUME
Press the soundbar’s or remote’s Volume + and – buttons to raise
and lower the system’s volume one step at a time. Hold down the
buttons to continuously raise or lower the volume. For the best
sound, we recommend turning your TV’s built-in speakers off.
Consult your TV’s owner’s manual to find out how to do this.
Note: You can control the soundbar with your own TV remote
control. See the “Using Your Own TV Remote (TV Remote
Learning)” section for more information.
Volume Buttons
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for JBL Cinema SB 450 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of JBL Cinema SB 450 in the language / languages: English as an attachment in your email.

The manual is 0,76 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info