Manual JB systems MIX6usb (page 4 of 36) (English, German, Dutch, French, Portuguese, Spanish)

756975

Zoom out

Zoom in

1/36

ENGLISH OPERATION MANUAL

JB SYSTEMS® 2/33 MIX6 USB

 To prevent fire or shock hazard, do not expose this appliance to rain or moisture.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance or may even cause damages.

 This unit is for indoor use only.

 Don’t place metal objects or spill liquid inside the unit. No objects filled with liquids, such as vases, shall be

placed on this appliance. Electric shock or malfunction may result. If a foreign object enters the unit,

immediately disconnect the mains power.

 No naked flame sources, such as lighted candles, should be placed on the appliance.

 Don’t cover any ventilation openings as this may result in overheating.

 Prevent use in dusty environments and clean the unit regularly.

 Keep the unit away from children.

 Inexperienced persons should not operate this device.

 Maximum save ambient temperature is 40°C. Don’t use this unit at higher ambient temperatures.

 Minimum distances around the apparatus for sufficient ventilation is 5cm.

 Always unplug the unit when it is not used for a longer time or before you start servicing.

 The electrical installation should be carried out by qualified personal only, according to the regulations for

electrical and mechanical safety in your country.

 Check that the available voltage is not higher than the one stated on the rear panel of the unit.

 The socket inlet shall remain operable for disconnection from the mains.

 The power cord should always be in perfect condition. Switch the unit immediately off when the power cord

is squashed or damaged.

 Never let the power-cord come into contact with other cables!

 When the power switch is in OFF position, this unit is not completely disconnected from the mains!

 This appliance must be earthed to in order comply with safety regulations.

 In order to prevent electric shock, do not open the cover. Apart from the mains fuse there are no user

serviceable parts inside.

 Never repair a fuse or bypass the fuse holder. Always replace a damaged fuse with a fuse of the same

type and electrical specifications!

 In the event of serious operating problems, stop using the appliance and contact your dealer immediately.

 Please use the original packing when the device is to be transported.

 Due to safety reasons it is prohibited to make unauthorized modifications to the unit.

INSTALLATION GUIDELINES:

 Install the unit in a well-ventilated location where it will not be exposed to high temperatures or humidity.

 Placing and using the unit for long periods near heat-generating sources such as amplifiers, spotlights, etc.

will affect its performance and may even damage the unit.

 The unit can be mounted in 19-inch racks. Attach the unit using the 4 screw holes on the front panel. Be

sure to use screws of the appropriate size. (screws not provided) Take care to minimize shocks and

vibrations during transport.

 When installed in a booth or flight case, please make sure to have good ventilation to improve heat

evacuation of the unit.

 To avoid condensation to be formed inside, allow the unit to adapt to the surrounding temperatures when

bringing it into a warm room after transport. Condense sometimes prevents the unit from working at full

performance.

CLEANING THE APPLIANCE:

Clean by wiping with a polished cloth slightly dipped with water. Avoid getting water inside the unit. Do not

use volatile liquids such as benzene or thinner which will damage the unit.

CONNECTIONS

Always use good quality cables to prevent bad audio quality.

Be sure to turn off the mixer before you make changes to the different connections.

This symbol means: Safety Class I appliance

ENGLISH OPERATION MANUAL

JB SYSTEMS® 3/33 MIX6 USB

In this manual we talk about “line inputs”. This is a global name for inputs with a level between 750mV and

2V. This includes tuners, videos, CD-players, etc.

There are many ways to connect audio equipment to this mixer. Just keep the following remarks in mind:

 Always connect cinch cables in the same way:

o white or black cinch connector  left channel

o red cinch connector  right channel

 Some inputs on the back panel have the possibility to receive a USB, phono or line input. Make sure to

assign the associated switch correctly:

o When you connect a CD-player, Cassette deck, MD-player, tuner, video recorder etc. don’t

forget to put the associated switch to “LINE”.

o When you connect a turntable don’t forget to put the associated switch to “PHONO”.

o When you connect a PC don’t forget to put the associated switch to “USB”.

 Many Turntables have a GND-connection. It is preferable to connect this signal ground to the MIX6 USB.

Use the GND-connections, close to the signal input connectors.

 The record input of an analog recording device can be connected to the record output of the MIX6 USB to

make analog recordings.

FUNCTIONS (FRONT)

1. 3-BAND TONE CONTROL : The frequency can be controlled. In the center position the tone control is

flat. (switched off)

2. MIC VOLUME: Used to adjust the level of the microphone.

3. MIC ON/OFF SWITCH: Used to switch the microphone on/off

4. PEAK LED: Facilitates proper setting of input gain levels. The LED lights up when the signal after the

Gain control (5) reaches 0dB. Warning: the LED should only light up from time to time. If it’s on

continuously, you should turn down the gain level (5) to avoid distortion.

5. GAIN LEVEL: Adjusts the input level on each channel, range goes from zero to maximum. Use this

control to adjust the level at about 0dB (see PeakLED ‘4’).

6. 3-BAND TONE CONTROL : The frequency can be controlled. In the center position the tone control is

flat. (switched off)

7. INPUT SOURCE SELECTOR: Used to select the correct input on each channel: phono, line or USB.

There are also additional input selectors on the back.

Hint: Line, Aux, CD, Tuner, etc… are different names for inputs with almost the same signal levels.

8. CHANNEL FADERS: Used to control the level of each channel. MIX6 USB uses high quality smooth

dual-rail 60mm DJ-faders for maximum reliability.

9. LED VU METER: Accurate level meter. Very important: If you want a nice and clean sound, please pay

attention the VU-meters. Most DJs use this important instrument as a “flashy light effect” . They try to

push the meter constantly to its maximum. Let’s be clear: a good DJ wants a clean, undistorted sound.

Levels over 0dB mean “distortion” so please keep an eye on the meter! 

10. AUX INPUT: can be used to connect an MP3 player, smartphone, etc. to channel 4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of JB systems MIX6usb in the language / languages: English, German, Dutch, French, Portuguese, Spanish as an attachment in your email.

The manual is 1,61 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

JB systems MIX6usb Manual

Product: