540266

Jata CP1025N Manual

8
Zoom out
Zoom in
Previous page
1/16
Next page
8
• When placing the appliance on it stand, ensure that the surface on which the stand is placed
stable.
• Do not leave unattended while in use.
• Always unplug the appliance from the mains when filling the tank with water.
• Avoid any contact between the cable and the hot parts of the iron.
• Do not leave the iron in a vertical position. Leave it always in its supporting in an horizontal
position.
• During the first use it is possible that the products used in the manufacturing process of the
appliance may contaminate the steam. We recommend that you allow the steam to flow for a
few minutes before starting to iron.
• The iron may have some smoke and / or smells during the first few uses. This is completely normal
in this kind of appliances.
• This appliance has been designed for domestic use only.
• The possible rests of water in the tank are due to the quality controls done in our production
lines.
• The cleaning and maintenance done by users, can not be done by children without any supervision.
• If the cable were to deteriorate it must be changed by an Authorised Service Centre.
INSTRUCTIONS OF USE
• For a correct functioning the appliance must be on a flat surface.
• Remove the tank (10) by keeping pressed the release button (11) and pulling out by the water
tank.
• With the help of a bottle or a jug or directly from the tap pour water into the tank (10). Do not
go over the water tank (MAX) indication. In the case of very hard waters you may use distilled
water.
• Replace the water tank to its original position and press it until the release pusher (11) is fixed.
Before doing this operation be sure the bushing for water situated inside the tank is correctly
fixed pressing it downwards in the direction indicated by the arrow .
• Set the iron temperature selector (5) to its maximum position (MAX) by turning it clockwise. If
you wish a lower temperature on the sole plate leave the temperature selector in ( ) position.
• Plug the appliance into the mains and push the iron on switch (7). The steam indicator light (8)
starts flashing and the iron indicator light (4) will light on.
• When this operation is done, the iron and the steam chamber will start heating.
• Await until the steam pilot light (8) change from flashing to get fixed and the iron pilot
light (4) goes off. At this moment the appliance is ready to be used.
OUTLET STEAM SELECTOR
• The steam outlet selector (2) has 3 positions. You can select the desired steam by turning this
selector:
Position : Steam.
Position : Frontal steam.
Position :Steam + frontal steam.
STEAM IRONING
• Remember that the iron temperature selector (5) must be set to its maximum position or in the
steam position ( ).
• Press with the index finger the steam button (1) for the steam begin to flow. It is advisable to use
the button in short intervals.
ATTENTION:
When pressing the steam pusher the pump starts to pass water intermittently to the
steam chamber. This intermittent noise of the pump is absolutely normal.
• When the water level is down, the low water pilot light (9) will start to light on intermittently
and it will stop the pump noise. You can fill the tank.
… 8 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jata CP1025N at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jata CP1025N in the language / languages: English, French, Italian, Portuguese, Spanish as an attachment in your email.

The manual is 0,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info