472831
11
Zoom out
Zoom in
Previous page
1/43
Next page
9
Changing Needle
Selecting Thread and Needles
For general sewing, use needle size 11/75 or 14/90. A
fine thread and needle should be used for sewing
lightweight fabrics, so the fabric will no be marred. Heavy
fabrics requires a needle large enough to the fabric
without fraying the needle thread.
Always test the needle size on a small pierce of fabric,
which will be used for actual sewing.
In general, use same thread for needle and bobbin.
When sewing stretch, very fine fabrics and synthetics,
use a BLUE TIPPED needle. The blue tipped needle
effectively prevents skipped stitches.
Fabric
Light
Thread
Needle
Medium
Heavy
Lawn
Georgette
Tricot
Wool,
Polyester
Cotton,
Polyester
Fine jersey
Wool
Denim
Jersey
Coating
Quilting
Silk #80-100
Cotton #80-100
Synthetic #80-100
Silk #50
Cotton #60-80
Synthetic #50-80
Cotton #50
Silk #50
Cotton #40-50
Synthetic #40-50
Silk #30
Cotton #50
#9/65–11/75
#11/75–14/90
#14/90
#14/90–16/
100
#16/100
CAUTION:
Turn off the power switch when changing a needle.
q Needle clamp screw
w Needle clamp
e Flat side
z Raise the needle to its highest position by turning the
handwheel counterclockwise, and lower the presser
foot. Loosen the needle clamp screw q by turning it
counterclockwise. Remove the needle from the needle
clamp w.
x Insert a new needle into the needle clamp w with the
flat side e to the rear. When inserting the needle into
the needle clamp w, push it up as far as it goes. Tighten
the needle clamp screw q firmly by turning it clockwise.
c To see if the needle is good, place the flat side of the
needle onto something flat (needle plate, glass, etc.).
The gap between the needle and the flat surface should
be consistent. Never use a bent or blunt needle.
A damaged needle can cause permanent snags or runs
in knits, fine silks and silk-like fabrics.
q
w
e
z
x
c
11


Need help? Post your question in this forum.

Forumrules
1

Forum

janome-dc4030

Reset search

  • i just got a janome model DC4030PR is the same as the DC4030 thanks Submitted on 30-1-2024 at 01:14

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Janome DC4030 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Janome DC4030 in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Janome DC4030

Janome DC4030 User Manual - Dutch - 43 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info