602020

Janome 8100 Harmony Manual

35
Zoom out
Zoom in
Previous page
1/63
Next page
33
Darning
q R: Automatic buttonhole foot
z Pull the button holder to the rear.
x Place the garment under the presser foot. Press the
up/down needle button key twice to pull up the
bobbin thread.
Remove the fabric to the left to draw both threads
under the presser foot and put the fabric under the
foot again.
c Place the needle where you would like to sew and
lower the foot. Press the foot control.
The machine will lock stitch, sew 16 rows of
darning, lock stitch and stop automatically.
The machine will lock stitch, sew 16 rows of
darning, lock stitch again and stop automatically.
* The size of darn cycle is variable. However, the
maximum stitch length is 2 cm (3/4˝) and the
maximum stitch width is 0.7 cm (1/4˝).
w
Button holder
e Foot hole
r Starting point for darning
t 2 cm (3/4˝)
y 0.7 cm (1/4˝)
[For darning a length of less than 2cm (3/4˝),]
v For darning a length of less than 2 cm.
First stop the machine after sewing the desired
length and then press the reverse button. The
required length has now been determined. Now,
restart the machine and continue sewing until the
machine stops automatically.
b Turn the fabric to change the sewing direction for
repeat sewing from step 1 to 3.
u
Reverse key
i Length required
o Starting point for darning
[To memorize darning stitches:]
When you press the memory key after step 3 and 4
you can repeatedly sew the samesize darn to repair a
side rip.
[To adjust the balance of the darning stitches.]
If one side of the darn is higher or lower than the
other, make them even by pressing the “ – ” or “ + ”
key between 1 and 5.
!0
Stitch width, Stitch length key
!1 When the left side is lower
!2 Select “ 1 ” or “ 2 ” to balance the stitches.
!3 When the right side is lower
!4 Select “ 4 ” or “ 5 ” to balance the stitches.
!5 This indication will be shown when you press the
Memory key.
,
,
,
,
q
w
e
t
y
r
u
i
o
!0 !5
!1 !2 !3 !4
zxc
vb
… 35 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Janome 8100 Harmony at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Janome 8100 Harmony in the language / languages: English as an attachment in your email.

The manual is 1,44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info