603247
32
Zoom out
Zoom in
Previous page
1/36
Next page
32
DE FR ENEN
Dis
p
la
y
dAtnetnoc eht teS
j
ustment ran
g
e The default value
AdJ
temperature correction
-5 ~ 5
-2.5
It is used to correcttheerror,the measured values thesensor
. When you set it, the LCD displays the correction
value. After three seconds, the LCD displays the measured value after correction.
PrG
2+57 / 1+6 / 2+5edom emit-doirep ehT
5+2Monday to Friday to set the same and Saturday to Sunday to set the same
6+1Monday to Saturday to set the same, Sunday is independent
7Monday to Sunday is same setting value.
LtP
FFOelbasiD :FFO / elbanE :nOezeerfitnA
Low temperature protection, what is suitable for the water system To prevent the pipe at low temperature was
freezing.
Sen
Sensor or temperature control mode I
N: Built-in OUT: External
ALL: Dual temperature control
IN
IN internal control, room sensor Out external control, floor sensor ALL double temperature double
control, the internal room temperature sensor, external sensor overheating protecting
tOP
External temperature sensor limit
40-80 50
The sensor is set to ALL, the temperature limit external sensor value
dt0
Internal sensor hysteresis
0.5-4 1
Built-in temperature sensor hysteresis
dt1
External sensor hysteresis
0.5-5
3
External temperature sensor hysteresis
bL
no syawlA :nOsutats gnithgilkcaB
OFF Auto turn off after 5sec
OFF
Backlight lighting mode, can be set according to personal preference
Sat
emit yreve ta sutats ffo :FFOrewop-er ta sutatS
On: the same as previous,
OFF
Used to control the power state o
f the boot
deF
Restore factory settings Restore factory settings To restore the default settings
the error and solution of Common system
1. Nodisplay
Power supply system is having problems or power is supplied incorrectly, please check
if the inlet wire is normal.
If the connection is not right, please wired up as the wiring diagram on the back side.
The thermostat of the working environment temperature is too low, please note the
thermostat temperature range.
If the temperature is lower than -5 °C, the thermostat cannot normally display.
Power supply box and the motherboard Coupling is not connected correctly, please
connect correctly.
Power supply box and the motherboard Coupling is opposite inserted, please mind
the direction
Power supply box and the motherboard Coupling is broken, please don‘t overexert.
Coupling length is 6cm,
the installation must be careful. If damaged, no replacement.
correct the error, the sensor
,setting item
protect
from
temperature control mode at different
sensor setting
IN: temperature control mode at different sensor setting OUT: control by oor sensor, only with external sensor
ALL: Dual temperature control, the heater stop when room temperature > setting value or oor temperature > setting value (tOP)
oor-temperature‘s limited value
oor-temperature limited value with ALL mode (Sen)
value
value
value
value
bootstatus when boot
boot status, off status or continue previous status
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jago RMTMS01 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jago RMTMS01 in the language / languages: English, German, French as an attachment in your email.

The manual is 1,89 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info