555013
2
Zoom out
Zoom in
Previous page
1/2
Next page
JK-05 PROFI GSM KIT 2/4 MGK55007
4. Detectors and accessories installation
a) Install the JA-60N magnetic detector to a door (antenna
pointing up or down)
b) Install the JA-60P motion PIR detector
c) Select Instant or Delay reactions via the DIP switches
inside the detectors.
d) Connect the detector batteries (pull out the red tape to
activate the batteries)
e) Attach the keypad to the desired location
f) Plug the UC-260 wireless siren into a power socket.
g) Test the wireless doorbell button and install it.
5. Enrollment of additional accessories
If you install additional detectors (max. 32), you have to enroll
them. The system should be in the P mode (if not enter F0 6060):
a) Press 1 to enter the learning mode*
b) The next free detector position will be displayed on the
keypad.
c) Install batteries into all new detectors step by step to enroll
them (system will automatically offer the next free position)
d) To scroll through the sensor positions, press 1 (up) or 7
(down)
e) To enroll a second detector to an occupied position press 5
before you install the detector batteries
f) To exit the learning mode press the N key
The wireless keypad (JA-60F) enrolls after you install its battery
while in the learning mode.
The remote control (RC-4x) enrolls after you press and hold
both the
and buttons while in the learning mode.
The wireless outdoor siren (JA-60A) enrolls after it is powered
up while in the learning mode
To enroll the control panel to UC receivers enter 299 on the
keypad while in the P mode
Check the manuals of individual items for more details
*Learning mode will also be entered after shorting the Reset pins
in the control panel.
6. Detector and controller testing
a) The system should be in P mode (if not, enter F0 6060)
b) Trigger the detectorstheir addresses (1=door and 2=PIR)
should be displayed (if the PIR detector does not react, re-
enter its test mode by opening and closing its cover)
c) Press button
on the RC-4x remote control c2 will be
indicated on the alarm display
A
attach
C
open
B
click
rear tamper
lever
Don't over-tighten
this screw
2
2,5
1,5
1
0,5
1,6 3,7
12
range
[m]
height
[m]
120
º
1
2
m
zone A
zone B
zone C
zone A
zone B
zone C
JA-60P coverage
Avoid locations facing windows or close to heaters
JK-05 PROFI GSM KIT 3/4 MGK55007
7. Radio signal strength measurement
a) While in P mode, press 1 and then using 7 scroll to position 1
b) Press 8 to start measuring
c) Activate the door detector to view its signal strength
d) Using the 1 key, scroll to the next position (2=PIR) and
check its signal strength (if the PIR detector does not react,
re-enter its test mode by opening and closing its cover)
e) Repeat step d) to check all enrolled items. The wireless keypad
(c1) signal is indicated after you trigger its tamper. The remote
control (c2) is indicated after you press button
.
f) Change the location of an item if its signal is lower than 2
g) Return to P mode by pressing the N key
8. GSM communication testing
a) Dial your mobile number from the SMS phone. Hang up after it
rings. This will display the system’s SIM card number on your
mobile phone.
b) Call back the system number using your mobile. Let the SMS
phone ring until the system answers your call (you will hear a
beep). Then enter the installer remote access code 0000 on
your mobile.
c) Now the mobile should work as a system keypad. Press the
# key to exit P mode and re-enter it by keying
0 6060
d) End the phone call
e) From your mobile, send a command SMS with MO in it to the
system. You should then receive a status report reply
f) Type some test text on the SMS phone and send it as an SMS
to your mobile.
g) You can also store your mobile phone number in the SMS
phone memory so that the end user can easily call you in future.
9. Programming the system
a) The system should be in P mode (if not enter F0 6060)
b) Using the following sequences you can program:
Function Sequence
Comments
Your installer code* 5 xxxx xxxx
6060 = factory default
xxxx = new code
Installer remote
access code*
94 xxxx F0
0000 = factory default
xxxx = customized code
User remote access
code*
94 xxxx F1
1111 = factory default
xxxx = new code
Exit delay
20x
3=30sec factory def.
Entrance delay
21x
3=30 sec factory def.
Alarm duration
22x
4=4min factory def.
Alarm SMS reporting
71 yyy..y F0
72 yyy..y F0
Alarm SMS + phone
call reporting
73 yyy..y F0
74 yyy..y F0
Alarm & arming SMS
reporting
75 yyy..y F0
76 yyy..y F0
Alarm phone call only
77 yyy..y F0
Technical trouble
SMS reporting
78 yyy..y F0
yyy..y = phone number
if 001 is entered the
SMS will go to the SMS
phone (free of charge) –
the SMS phone will work
as the system’s LCD
keypad
7nF0 erases number n
User 1 to 4 arming
reporting to 75 & 76
80x
x=1 enabled
x=2 disabled
GSMLink
pre-registration
972 yyy..yF0
yyy..y = your mobile
number (international
format 00 country …)
Time & date entry
4 hh mm DD MM YY
See control panel installation manual for more details
* Must be changed
10. SMS text editing
Factory default SMS texts in the system can be modified easily by
Jablotron’s Comlink software. You can also change individual texts
by sending the following SMS from the SMS phone to telephone
number 001 (it goes directly to the control panel - free of charge).
yyyyTXTz,text,z,text,z,text.....
yyyy = installer remote access code (0000 = factory default)
= separator, space can also be used
z = text index, see the following table
text = new text (no commas or periods/full stops allowed)
z Factory default text z Factory default text
700 Alarm system reports: 415 Wireless detector #15
201 Controller #1 416 Wireless detector #16
202 Controller #2 501 User code #1
203 Controller #3 502 User code #2
204 Controller #4 503 User code #3
205 Controller #5 504 User code #4
206 Controller #6 505 User code #5
207 Controller #7 506 User code #6
208 Controller #8 507 User code #7
401 Wireless detector #1 508 User code #8
402 Wireless detector #2 509 User code #9
403 Wireless detector #3 510 User code #10
404 Wireless detector #4 511 User code #11
405 Wireless detector #5 512 User code #12
406 Wireless detector #6 513 User code #13
407 Wireless detector #7 514 User code #14
408
Wireless detector #8
z Factory default
commands
409 Wireless detector #9 703 AM
410 Wireless detector #10 704 DM
411 Wireless detector #11 705 MO
412 Wireless detector #12 706 ME
413 Wireless detector #13 710 PGON
414 Wireless detector #14 711 PGOFF
A complete list of all texts is in the control panel installation manual
11. Finishing the installation
a) Fill in the information on the sticker label and attach it inside
the keypad cover.
b) Switch the system to standby (by pressing the N key)
c) Instruct the user on how to operate the system
d) Show that after you pickup the SMS phone and press #, the
phone keypad operates the system.
Ev ent
Source or mode
Wireless item
Additional
functions
Arm
Disarm
+ Panic
RC-42
12. Keypad operation
Entry Function
user code
Arming / Disarming
F1 /
Arming without code
F2 /
Partial arming
F3 /
Door lock opening
F4
Memory reading
F5 New master code (example: F5 1234 2789 2789)
F6 User code setting (example: F6 1234 03 3344)
F7 /
Disarming under duress
F8
Appliance control (F81 = ON, F80 = OFF)
F0 M.code
User test mode (example F0 1234)
N
Escape & fault detail reading
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JK-05 PROFI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JK-05 PROFI in the language / languages: English as an attachment in your email.

The manual is 0,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info