Manual Jablotron JA-82Y (page 7 of 13) (English)

555059

Zoom out

Zoom in

1/13

The JA-82Y GSM communicator installers manual 7/7 MDL51108

7.10. URL / IP address for data transmission

The communicator supports transmission of special data (e.g. visual information

from JA-84P) from the system to a set IP address, which can be set by the

following sequence:

013 xx..x∗0

where:

xxx...x is the IP address and port – entry format example:

013 ∗8 192 168 021 123 07070 ∗0

Where

∗8 (auto-converts to #) signifies an IP address which must have 12

digits and must be followed by the 5 digits of the port number (no

separators).

To erase the IP enter 013∗0.

Notes:

• if no devices supporting this feature are in the system, do not set any IP

address.

• the address can also be entered in URL format through OLink, the system

keyboard allows digits only

Factory default setting: URL - lib1.jablotron.cz:7070

7.11. Locking the ARC settings

All settings which affect reporting to ARCs can be locked by a digital code. To do

so, enter:

091 xx..x*0

where:

xx..x is your code (4 to 8 digits)

Notes:

• Exiting service mode after the locking code has been entered will lock all the

settings affecting ARC communication (see the sequence list in section 13).

• If ARC programming is locked, then it can be temporally enabled in service

mode by entering 092 xx..x

∗

0 where xx..x is the locking code. It will then

relock on exiting service mode.

• The ARC settings can be permanently unlocked by entering 091

∗

0 (the code

can be erased only if ARC setting is unlocked)

Factory default setting: ARC settings unlocked

7.12. Repeated ARC communication

The communicator tries to send the report to the main telephone number. If this

fails, it tries the backup number and in the case of failure, the communicator

repeats the attempt with a delay which is set by the following sequence:

0001 p mmss

where:

p 1=ARC1, 2=ARC2

mmss time in minutes, seconds

Factory default setting: 15s

7.13. Number of repeated attempts

Defines how many times in a row the communicator will try to transmit

information to the ARC after an unsuccessful attempt. It is possible to set up to 9

repeated attempts. They are set by the following sequence:

0002 p n

where:

p 1=ARC1, 2=ARC2

n 1 to 9 attempts

Factory default setting: 2 attempts

7.14. Integrated image transmission module

The communicator contains a built-in module for the reception of images from JA-

84P detectors. The device must be set up properly for the successful transfer of

photographs to the server (see 7.10) The Jablotron image viewing server is

situated at http://img.jablotron.com.

IP address for image sending:

URL: lib1.jablotron.cz:7070 IP: 77.104.220.129:7070

Warning: The set or modified parameters only take effect after you exit service

mode.

The signalling of image transmission on the module

• Once the images have been taken by a JA-84P, they are immediately sent to

the GSM communicator and subsequently to a secure server (if it has been

set).

• The transmission from a PIR to the communicator is indicated by green LED 1

being permanently lit (on the left under the SIM card holder) see fig. 1

Communicator description:.

• Transmission to the server is signalled by a flashing green LED.

• Successful transmission is confirmed by a long green-LED flash and

unsuccessful transmission is reported by rapid flashes of the green LED.

Successful transmission from the GSM communicator to the server is

confirmed by a long flash of the red LED, unsuccessful transmission is reported

by flashing of the red LED.

Notes:

• The total time of transmission to the server is about 20s.

• If the signal is weak, the transmission can take longer (the lost data is sent

repeatedly). Each image contains the date and time of acquisition which is

taken from the control panel internal clock.

• The synchronization of time from the moment the batteries are inserted into a

JA-84P takes 60 minutes.

7.15. Updating the communicator

The communicator can be updated by any authorized person. (i.e.firmware,

language and voice settings). Current firmware is accessible on

www.jablotron.com. Before updating, save your communicator settings to the

OLink database. For updating, it is necessary to have one of these interfaces: JA-

80T, JA-80BT or JA-82T and the program OLink (v.2.0 or higher). Uploading via a

JA-82T is faster. Be careful not to do anything during the updating process (don´t

disconnect the cable or do anything with the PC) and wait till the end.

Restart the communicator after the updating procedure via the 893 sequence, or

turn off the main power and battery and after a few seconds turn them on again.

Then wait for 1 minute. During this operation do nothing with the system till the red

LED stops shining.

Updating can change the device registration key which you need for remote

access via the internet.

8. Further guidance on the communicator

8.1. How the communicator sends reports

1. If there is a need to report an event (e.g. an alarm) then the

communicator sends data to ARC1 (the communicator tries the main

phone number / IP address / URL. If unsuccessful then it tries the

backup number / IP address / URL and if still unsuccessful, it repeats

the action).

2. Then it sends data to ARC2 in the same way if programmed as an

independent ARC. If ARC2 is programmed as the backup to ARC,1

then the data will only be sent to it if transfer to ARC1 has been

unsuccessful.

3. Then the unit sends SMS reports (1st tel. number, 2nd tel. Number,..)

4. Then the unit transmits a voice message to each telephone number

with this setting. Each programmed number is called only once

regardless of whether the call has been answered or not. Pressing the

# key cancels calling other numbers and the system enters keypad

simulation mode in which it is possible to fully control the system.

If all previous attempts to send data to ARCs have been unsuccessful, the next

attempts occur after the programmed repeat period (see 7.6).

If an alarm is cancelled by a user while it is being reported, any unsent

SMSes and unperformed call reports are cancelled, but the ARC still gets a

complete set of reports about events in the system.

8.2. The communicator’s LED

The red LED on the communicator board indicates as follows:

• It is lit for a period during registration to a GSM network

• when sending an SMS message, the LED is lit for 1 second

• the LED flashes rapidly during the detection of an incoming call

• It is lit permanently during remote access from a telephone

• A permanently lit LED could indicate that the communicator is not registered

to a GSM network

• The LED flashes during remote-access data transfer

The green LED on communicator board indicates as follows:

• Flashes for a 2 seconds when communicator is connected to control

panel

• Flashes once a second when pictures are transmitted (see 7.14)

•

8.3. Notes on entering service mode

If the system is switched to service mode:

1. The communicator completes the current transmission to the ARC.

2. The current phone call reporting is terminated.

3. Unfinished SMS and call reports are erased (they are not transmitted

after the service has finished).

4. Unsent ARC reports are only erased if ARC tel. numbers / IP

addresses / URLs or the ARC communication format or the installation

ID are changed.

5. Fault restoration reports are sent to the ARC even in service mode.

6. Changes to communicator settings do not take effect until service

mode has been exited.

8.4. Remote access via the Internet

The system can be accessed remotely via OLink 2.0.1 and higher. This allows

complete programming by installers (it is necessary to know the service code) and

also operating the system by end users in the same way as if they were using a

keypad. To access the system remotely it is necessary to have:

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-82Y in the language / languages: English as an attachment in your email.

The manual is 0,22 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-82Y

Jablotron JA-82Y User Manual - English - 8 pages

Jablotron JA-82Y User Manual - Dutch - 14 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-82Y Manual

Product: