Manual Jablotron JA-80Y - GSM communicator (page 3 of 12) (English)

631261

Zoom out

Zoom in

1/12

The JA-80Y GSM communicator - 3 - MFJ55304

 if it is desired that the events be reported to the SMS phone connected

to the communicator then program tel. number 001 into the memory

 SMS report text consists of: installation name, event name, number and

name of the event source (device or code), date and time. Example:

“Report from your alarm: setting 47: device Time 01.08. 11:27”

 if other events or texts should be reported to a particular number,

change the communicator settings (see 5.4 and 5.5)

 when storing tel. numbers, if you key in ∗7 after the last digit of the

phone number (the symbol ∗ is also stored) and continue with one

more digit (1, 2, 3, 8 or 9), then if this tel. number calls the system, the

system will behave as if ”∗ digit“ had been keyed in just after the first

ring, i.e. as if it had been entered manually on the system keypad –

see section 3.5. Example: entering 81 5 777 777 777

∗

authorizes calls from tel. number 777777777 to trigger output PGY for

2 seconds (after the first ringing signal from this number the ∗9

command will be executed. The PGY output should be programmed for

a 2 sec. pulse function. This setting is suitable for opening an electric

door lock, automatic gate etc.

4.1. Programming

The most convenient programming is best done by a PC running

Comlink software or via the Internet and website: www.GSMLink.cz

or by

programming SMS – PRG sequence

Programming is also possible via the system keypad:

 The control panel must be in Service mode - if it is not, enter ∗0 Service

code (factory default: 8080) while the system is unset.

 Enter the relevant programming sequences – see the following description

 To exit service mode press the # key

5. Programming sequences

Function Sequence Options Factory default

Language setting 981 xx

xx=01 to 17 where:

01=EN,02=CZ,03=SK,04=NL,05=DE,06=PL,07

=DA,08=IT,09=PT,10=FI,11=NO,12=SV,

13=FR, 14=HU, 15=RU, 16=TR, 17=SP

English

GSM signal strength

measurement

922

On keypad or in ComLink software range 0/4 to 4/4

In reply to STATUS SMS: range 0/9 to 9/9

exit by pressing #

Tel. number programming for

reporting to telephones

81 M xx..x ∗0

M = memory 1 to 8

xx..x = tel. number (max.20 digits)

keying in ∗9 = + and ∗7 = ∗

81 M ∗0 erases the number in memory M

all M1 to M8 erased

Selection of events to report by

SMS

82 M ec x

Selection of events to report by

phone call

83 M ec x

M = tel. number memory from 1 to 8

ec = event code (see 5.4)

x=1 report, x=0 no report

M1 & 2 alarms by SMS

M3 & 4 alarms by SMS and call

M5 & 6 alarms by SMS and call +

Set/Unset by SMS

M7 alarms by call

M8 technical faults by SMS (to installer)

SMS text editing*

Texts can be edited by Comlink software or by SMS instruction:

code TXT n,text,n,text... or by www.GSMLink.cz

via Internet

see 5.5

Enable reporting to phones 80 x

x=0 disabled

x=1 enabled (all programmed by 82.. & 83..)

x=2 enabled without reporting

setting/unsetting by users 41 to 50 (codes,

cards & key-fobs) and master code

setting/unsetting

enabled

Remote access 903 x

x=0 disabled

x=1 enabled (by phone and Internet)

enabled

Forwarding of incoming SMSes 926 x

x=0 no, x=1 yes = if the incoming text is not an

SMS instruction it will be forwarded to the first

programmed number in memories M1 to M8

yes

SMS instruction confirmation 927 x x=0 no, x=1 yes (by SMS reply) yes

Reaction to incoming calls 904 x

x=0: no reaction

x=1 to 8: answers after 1 to 8 rings

x=9: answers after the 2

call

answers after 5 rings (25s)

Simulated phone line function 951 x

x=0 tel. line (GSM gateway)

x=1 alarm system keypad

x=2 off

x=3 automatically calls an emergency tel.

number when the tel. receiver is picked up

tel. line

Emergency tel. number

952 xx..x ∗0

xx..x = tel. number (max.20 digits) erased

GSM signal dropout indication 921 x x=0 no, x=1 yes (15min. dropout =Fault) no

Phone microphone sensitivity 953 x

Phone speaker loudness 954 x

x=1 to 9 (9 = maximum) 5

Number to be periodically called

to maintain SIM card validity

924 xx..x ∗0 xx..x = tel. number (max.20 digits), 924∗0=erase

erased

Using an SMS instruction to

configure automatic SIM card

credit interrogation *

Via an SMS instruction to the alarm system: code CREDIT uu..u xx yyy zz where code = master or service

code, uu..u = GSM network command string to ascertain the credit (e.g. ∗104#) , xx=auto-interrogation

frequency in days, yyy=minimum acceptable balance, zz= the textual position at which the number showing the

balance starts in the reply message from the GSM provider. If the credit is lower than the minimum, the

provider’s SMS will be auto-forwarded to numbers M1 and M8 for someone to top up the pre-paid SIM card.

Getting your www.GSMLink.cz

registration code sent to your

mobile phone

910 xx...x ∗0

xx..x = your mobile phone number -

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80Y - GSM communicator in the language / languages: English as an attachment in your email.

The manual is 0,17 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80Y - GSM communicator

Jablotron JA-80Y - GSM communicator User Manual - English - 16 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80Y - GSM communicator Manual

Product: