554835
19
Zoom out
Zoom in
Previous page
1/22
Next page
Installation manual: Oasis security system JA-80K - 19 - MKE51801
B in an unsplit system: hot key for setting sections A and
B (e.g. partial night-setting of the garage and the ground
floor).
in a split system: hot key for setting section B (C is only
set if both sections A and B are set)
? Display of triggered detectors (e.g. open windows), fault
details and PGX / PGY status.
turning on the PGX output from the keypad (the same
effect as 81)
turning off the PGX output from the keypad (the same
effect as 80)
Notes:
The A and B keys only have a function if partial setting or
splitting are enabled.
The keys
and only control the PGX output if they have
been programmed for it, see 12.5.
13.1.5. Functions beginning with the key
The following functions are available to the user via the
keypad:
1 sets the entire system (the same as key ABC)*
2 sets section A (the same as key A)*
3 sets A and B, or just B (the same as key B)*
4 event memory recall (key 4 scrolls backwards) – the
control panel records max. 255 of the latest events
5 new Master Code/Card (5 MC NC NC)
6 access code/card programming (6 MC nn NC)
7 for operation while under duress (should be entered
before the access code to secretly signal distress)
8 PGX control (ON/OFF = 81/80 or enter 8 to trigger if a
pulsed switching reaction is programmed)*
9 PGY control (ON/OFF = 91/90 or enter 9 to trigger if a
pulsed switching reaction is programmed)*
0 To enter Service Mode (0 SC – factory default 8080) or
to enter maintenance mode (0 MC – factory default
1234)
The functions allow the system to be operated from a mobile phone
keypad (if the control panel is equipped with the relevant
communicator).
13.2. Programming access codes and cards
The system can be controlled by 4-digit codes or by access
cards, of the types PC-01 and PC-02 (EM UNIQUE 125kHz
standard).
The control panel has 1 service, 1 master and 50 user codes.
Only a numerical code can be used as a service code (factory
default 8080) – see the control panel programming section.
The master code can be a numerical code (factory default
1234) or an access card. Using this master code/card, other
users’ codes and cards can be programmed or erased. The
master code/card is usually used by the system administrator.
Each user from 01 to 50 can have a numerical code, or a
card, or both (factory default: all user codes and cards from 01
to 50 are erased).
If a user has both a code and a card, then it is possible to
program whether both a code and card must be presented to
the system for system access, or whether only one of them is
required (see 12.37).
The system does not allow the same code or card to be
programmed to multiple users. (if it is desired to move a
code/card to another user, the card/code has to be erased
from its current user first).
It is possible to display which code/card positions are already
occupied in maintenance mode (see 13.4.1).
The most convenient way to program codes and cards is by
using a PC running Comlink software.
The control panel allows a maximum of 10 unsuccessful
attempts in a row to enter a valid code or card. If exceeded, a
tamper alarm starts.
13.2.1. Programming access codes and cards
Abbreviation Name Number Sequence Notes
SC Service
1
5 NC NC
Only programmable in Service Mode.
NC = new code (must be entered twice) – a card cannot be used.
Factory-default service code: 8080
This code can be changed but not erased.
Example: 5 4567 4567
MC Master
1
5 MC NC NC
Only programmable if the system is totally unset (disarmed)
MC = master code or card (factory default 1234)
NC = new code or card entry – a numerical code has to be entered twice, but a
card only presented once
Either a code or a card can be programmed as a master code (to have both is
impossible).
The Master Code can be changed but not erased.
The Master Code’s reaction is set/unset and it is assigned to all sections.
To reset the Master Code to the factory default 1234, enter 291 in Service Mode
(this will only affect the Master Code).
To make handing over the system to the end user easier, we recommend
programming the system card (provided with the control panel) to the master
code.
Example:
5 1234 and then presenting the card to the keypad’s RFID reader
UC User
50
6 MC nn NC
Only programmable if the system is totally unset
MC = Master Code or card.
nn = user code or card position from 01 to 50.
NC = new code or card entry.
Factory default: all user codes and cards are erased.
Each user position can have both a card and a code programmed to it (by using
the sequence 6 MC nn NC twice)
Each user code can have its own reaction programmed by an installer in Service
Mode, and with a split system, codes can be assigned to different sections.
Example:
6 1234 12 4345 (code 4345 will be programmed to user position 12)
To erase codes/cards enter:
6 MC nn 0000 erases the code and the card in user position nn.
6 MC 00 UC erases the code UC (or card UC) if programmed to any user position.
6 MC 00 0000 erases all user codes and cards in user positions 01 to 50.
19


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80K at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80K in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80K

Jablotron JA-80K User Manual - English - 1 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info