Manual Jablotron JA-80K (page 14 of 22) (English)

554835

Zoom out

Zoom in

1/22

Installation manual: Oasis security system JA-80K - 14 - MKE51801

Unsetting (disarming) the system with a final door detector

• If a final-door detector gets triggered in a set (armed) system,

an entrance delay will begin with a duration of between 30 and

270 seconds.

• If a normal delayed detector gets triggered while the user

enters a building, the system starts an ordinary entrance delay

of between 5 and 45 seconds.

• If a final-door detector is triggered first, a longer entrance

delay will begin. If during this delay an ordinary delayed

detector is then triggered, the remaining entrance delay will

then be shortened to the delay associated with detectors of

this kind.

Note: Only use status-reporting detectors such as the JA-80M or JA-

82M, or the hard-wired inputs of wireless keypads, or the hard-wired

inputs of a control panel as final-door detectors. This mode is unsuitable

for pulse detectors such as JA-80P motion detectors, or the hard-wired

inputs of JA-80E hard-wired keypads which also have a pulse reaction.

Factory default setting: No final-door detectors in the system.

12.24. Partial setting (arming) or system splitting

The control panel can be configured in three ways as follows:

• the entire system sets and unsets together or,

• the system partially sets and unsets to protect only

certain parts of a house during the day, while people

are still present in the unset parts or,

• the system can be split into two independently

set/unset sections for two separate users and also with

a common section if desired.

Program as follows to configure the system as desired:

66x

where x =0 = unsplit system (setting/unsetting as an

entire system)

x=1 = partial setting (for setting sections A, AB,

or ABC)

x=2 = split system (sections A and B can be

set/unset independently by separate users,

with section C only being automatically set

when both A and B are manually set)

Notes:

• For an unsplit system, all intruder detectors are set/unset

immediately after the user sets/unsets the system. Assigning wireless

devices, access codes and keyfobs to various sections of the system

has no effect in this mode.

• Partial setting is especially suitable for homes and apartments where

the user wishes to protect different parts of the premises during the

day. Detectors can be assigned to three sections, A, B and C. Using

setting (arming) key A on the system keypad, you can set section A,

e.g. setting the garage area in the afternoon. Using setting key B you

can set sections A and B simultaneously e.g. in the evening before

going to sleep to protect the garage (section A) and the ground floor

of the house (section B). The ABC total-setting button is used when

leaving the home to set all sections, A,B and C. If you then use a valid

access code or card for unsetting (disarming), all sections will be

unset. The assignment of codes or cards to sections has no effect in

this mode.

• A keyfob can also be used for partial setting control. Buttons

and

can be programmed to set and unset the entire system, and

buttons

+ can be programmed for setting (arming) sections A

and AB respectively to partially set the system. (see 12.40 for details

on partial setting by keyfob).

• Split system mode is especially suitable where two families (A and

B) live in a single house or two companies (A and B) share one

building. The system behaves as two independent systems, one being

section A and the other, section B. There is also a common section C

which is only set if section A and section B are set at the same time.

and is commonly used for shared entrances, doors etc. Detectors can

be assigned to sections A, B or C. Access codes and cards can be

assigned to operate either section A or B (not both), or alternatively to

section C to access the entire building. The same is true for keyfob

access.

• Partial setting only has an effect on intruder detectors, i.e. detectors

with instant, delayed or next-delayed reactions. Detectors with fire,

tamper, panic and 24-hour reactions are always able to trigger their

kind of alarm immediately, whether their section is set (armed) or not.

Factory default setting: Unsplit system.

12.25. Automatic summer time (daylight saving time)

If enabled, this feature automatically offsets the system time to

that of summer time, or daylight saving time as it is also known,:

6801 automatic summer time enabled

6800 automatic summer time disabled

Note: If automatic summer time is enabled, the control panel’s internal

clock is automatically offset by +1 hour on March 31

at midnight. The

offset is then removed on October 31

at midnight to return to winter

time.

Factory default setting: automatic summer time disabled

12.26. Tamper alarm in response to an increase in

the number of triggered tamper sensors

This feature allows permanently triggered tamper sensors to be

ignored:

6811 ignore permanently triggered tamper sensors, i.e.

only react to an increase in the number of triggered

tamper sensors.

6810 react with a tamper alarm to all triggered tamper

sensors

Note: Ignoring permanently triggered tamper sensors is useful for

example when carrying a detached wireless keypad around with you

during installation as this avoids unnecessary tamper indication.

Factory default setting: react with a tamper alarm to all

triggered tamper sensors

12.27. Operating the PG outputs using ∗8 and ∗9

Using this feature the PGX and PGY outputs can be controlled

from the keypad by pressing the ∗8 and ∗9 keys (or keys

and

6821 control enabled

6820 control disabled

Notes:

• The PG outputs can only be operated from the keypad if they have

their ON/OFF or pulse functions enabled.

• In addition to controlling the PG outputs using keys

∗

8 and

∗

9, PG

outputs can also be controlled by access codes, access cards,

keyfobs and detector signals (see 12.40 and 12.41 for details).

• If a PG output should only be operated by a valid access code or

card, then control by

∗

8 and

∗

9 should be disabled and the codes and

cards should be programmed to control the PG outputs instead (see

12.41).

Factory default setting: control enabled

12.28. Permanent alarm status display for a set

system

The below sequence enables the permanent display of alarm

status on the keypad unit, even if the system is set.

6831 permanent status display enabled

6830 display time a maximum of 3 minutes if any section is

set (armed)

Notes:

• European legislation requires status displaying to be suppressed

within three minutes of setting (arming) the system, no matter how

much or little of the system is set. This feature can be used to ignore

this requirement if appropriate.

• The wireless keypad can continuously display the status if powered

by an external power supply. If powered by internal batteries the

keypad will turn off its display after 20 seconds of not being used ( in

Service Mode the display turns off after 15 minutes of no use by the

installer).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80K in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80K

Jablotron JA-80K User Manual - English - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80K Manual

Product: