Manual Jablotron JA-80K (page 10 of 22) (English)

554835

Zoom out

Zoom in

1/22

Installation manual: Oasis security system JA-80K - 10 - MKE51801

Device reactions and section assignment

(detectors,

key fobs, control panel and keypad inputs)

• A detector’s natural reaction can be INS, DEL or Fire

(selectable in the detector)

• The natural reaction of Control panel & Keypad wired

inputs is DEL

Keyfob natural reactions:

(or )= SET (arm) ,

(or

)= UNSET (disarm) and both simultaneously = Panic. If a

reaction from 2 to 8 is selected (see opposite), only the key

(or ) and double buttons + ( +

) will have it.

The

( ) button has no effect (can still be used for

controlling UC/AC receivers).

• Assignment to sections will only have an effect on partial

arming or if the system is split (except PG output control)

• For partial arming, a pair of keyfob buttons assigned to

section:

A has the effect:

(or )=SET A, (or )=SET AB

B has the effect:

(or )=SET A, (or )=SET AB

C has the effect:

(or )=SET ABC, (or )=UNSET

ABC

• In a split system, a keyfob button pair assigned to section:

A=SET/UNSET A, B =SET/UNSET B, C =SET/UNSET ABC

61 nn r s

Code (card) reactions and section assignment

• A code (card) may have the same kind of reaction as

devices

62 nn r s

nn = address 01 to 50

r = reaction

0 disabled (incl. tamper sensor)

1 Natural – this means:

for detectors=selected by

DIP switch in the detector,

for wired inputs=DELay,

for Codes

(cards)=SET/UNSET

2 Panic

3 Fire

4 24 hours

5 Next DELay

6 INStant

7 SET (arm)

8 PG control (s: 1=PGX,

2=PGY,3=PGX+PGY)

9 SET/UNSET (toggle)

s = section 1=A, 2=B, 3=C - has

to be entered even if the system

is not split and setting

(arming)has no meaning.

In a split system, a code (card)

assigned to C will SET/UNSET

all ABC sections

all Natural

in C

Enrollment by keying in production codes

60 nn xxxxxxxx

nn = address 01 to 50, xxxxxxxx = last 8 digits of the

production code (below the bar code on the device)

Automatic Daily Setting/Unsetting schedule

(arming/disarming)

64nahhmm

n – action sequence index (0 to

a – action:

0=no action

1=SET ABC

2=UNSET ABC

3=SET A

4=SET B (if unsplit then AB)

5=UNSET A (if unsplit then ABC)

6=UNSET B (if unsplit then ABC)

hh - hours, mm - minutes

No action

The scheduled

actions will happen

every day

Changing the service code 5 NC NC

NC = new code (4 digits) 8080 enter NC twice

Go to maintenance mode 292

switches to maintenance

mode

Setting the internal clock 4 hh mm DD MM YY

00:00 1.1.00

Editing keypad text

Text for device names, code names and PG output names are

stored in each individual keypad.

Press and hold the

? key to enter text editing

(the first character of the first address name

will start flashing). Then use keys:

and to select some text (or an address)

1 & 7 character selection (A,B,C,D...8,9,0)

4 & 5 cursor (to the left & right)

2 to erase a character

# = exit editing and save changes

Device

Only capital letters

can be entered this

way. If there are

multiple keypads,

each must be edited

individually this way

or all of them can be

easily programmed

via Comlink software

12.2. Exit delay time

An exit delay time occurs while setting (arming) the system.

During this time period delayed or next-delayed detectors can be

triggered without an alarm occurring. To program the delay time,

enter:

20x

where x is a number from 1 to 9 determining the

duration in steps of tens of seconds (1=10 s,

2=20 s,....)

If there is a final-door detector in the system then the

exit delay is multiplied by 30 s instead(1=30 s,

2=60 s,...)

Example: To program a 20 seconds exit delay, use the

sequence 202 (if there is a final door detector, a 60 seconds

delay will result) .

Factory default setting: x = 3

12.3. Entrance delay time

The entrance delay time is provided to unset (disarm) the

system after a first delayed detector has been triggered. To

program this time, enter:

21x

where x is an number from 1 to 9 determining the

delay in multiples of 5 seconds ( 1=5 s,

2=10 s,....)

If the entrance delay is triggered by a final-

door detector, then parameter x is multiplied

by 30 s instead. (1=30 s, 2=60 s,...) – in this

case it means that the entrance delay would

be six times longer than if it had been

triggered by an ordinary detector.

Example: To program a 20 seconds entrance delay, enter the

sequence 214 ( if the delay has been activated by a final-door

detector, a 120 seconds delay will result instead).

Factory default setting: x = 4

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80K in the language / languages: English as an attachment in your email.

The manual is 0,55 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Jablotron JA-80K

Jablotron JA-80K User Manual - English - 1 pages

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Jablotron JA-80K Manual

Product: