554849
2
Zoom out
Zoom in
Previous page
1/2
Next page
Bluetooth adapter JA-80BT 2 / 2 MHY51900
The JA-80BT Bluetooth adapter
The JA-80BT Bluetooth adapter (interface) allows you to establish a wireless
connection between systems of the JA-8x series or the JA-6x series and PCs
equipped with Bluetooth connectivity. You can connect the adapter to the control
panel’s digital bus connector via an RJ cable supplied with the package. The
computer is assumed to have all the hardware/software installed necessary for
Bluetooth communication.
Pairing the adapter
1. Connect the JA-80BT to the control panel’s digital system bus. After being
connected, the device will initialise for about 15 seconds which is indicated by blue
LED flashing. (The LED stops flashing as soon as the initialisation period ends.)
2. Start a search for BT devices using the Bluetooth driver program running on your
PC. To do so, follow the driver’s instructions *.
3. After a “JA-80BT” device has been discovered, click the “Pairing” button. A dialog
box should appear which prompts you to type in a code – a connection security
code. Key-in the four digit PIN number which is printed on the label attached to the
JA-80BT adapter.
4. After the devices have been paired a virtual COM port (e.g. COM5) is created on
the computer. This port is accessible to the ComLink software.
5. On start-up, the ComLink application scans through all existing computer ports. If
an active JA-80BT COM port is found, ComLink starts to communicate via this
port. This communication is indicated on the JA-80BT by a blue LED being
constantly lit.
6. Exiting the ComLink application or switching to Offline mode will end
communication and turn the blue LED off.
*Note: The pairing routine may vary depending on the drivers installed on your PC.
Specifications
Connector RJ-4
Power supply from the digital bus
Consumption (standby / maximum) 6 mA / 25 mA
Control panel connection cable length 1 m
Built-in decoder data conversion of JA-8x/6x to Bluetooth
Compatibility ComLink version 60 and higher
FCC ID VL6JA80BT
Jablotron Ltd. hereby declares that the JA-80E is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC and complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the user´s
authority to operate the equipment. The original of the conformity assessment can be found at
www.jablotron.com
, Technical Support section.
Note: Although this product does not contain any harmful materials we suggest you return
the product to the dealer or directly to the producer after use.
Bluetooth adapter JA-80BT 2 / 2 MHY51900
The JA-80BT Bluetooth adapter
The JA-80BT Bluetooth adapter (interface) allows you to establish a wireless
connection between systems of the JA-8x series or the JA-6x series and PCs
equipped with Bluetooth connectivity. You can connect the adapter to the control
panel’s digital bus connector via an RJ cable supplied with the package. The
computer is assumed to have all the hardware/software installed necessary for
Bluetooth communication.
Pairing the adapter
1. Connect the JA-80BT to the control panel’s digital system bus. After being
connected, the device will initialise for about 15 seconds which is indicated by blue
LED flashing. (The LED stops flashing as soon as the initialisation period ends.)
2. Start a search for BT devices using the Bluetooth driver program running on your
PC. To do so, follow the driver’s instructions *.
3. After a “JA-80BT” device has been discovered, click the “Pairing” button. A dialog
box should appear which prompts you to type in a code – a connection security
code. Key-in the four digit PIN number which is printed on the label attached to the
JA-80BT adapter.
4. After the devices have been paired a virtual COM port (e.g. COM5) is created on
the computer. This port is accessible to the ComLink software.
5. On start-up, the ComLink application scans through all existing computer ports. If
an active JA-80BT COM port is found, ComLink starts to communicate via this
port. This communication is indicated on the JA-80BT by a blue LED being
constantly lit.
6. Exiting the ComLink application or switching to Offline mode will end
communication and turn the blue LED off.
*Note: The pairing routine may vary depending on the drivers installed on your PC.
Specifications
Connector RJ-4
Power supply from the digital bus
Consumption (standby / maximum) 6 mA / 25 mA
Control panel connection cable length 1 m
Built-in decoder data conversion of JA-8x/6x to Bluetooth
Compatibility ComLink version 60 and higher
FCC ID VL6JA80BT
Jablotron Ltd. hereby declares that the JA-80E is in compliance with the essential requirements
and other relevant provisions of Directive 1999/5/EC and complies with part 15 of the FCC rules.
Operation is subject to the following two conditions: 1. This device may not cause harmful
interference, and 2. This device must accept any interference received, including interference that may cause
undesired operation.
CAUTION: Changes or modifications no expressly approved by Jablotron could void the user´s
authority to operate the equipment. The original of the conformity assessment can be found at
www.jablotron.com
, Technical Support section.
Note: Although this product does not contain any harmful materials we suggest you return
the product to the dealer or directly to the producer after use.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-80BT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-80BT in the language / languages: English as an attachment in your email.

The manual is 0,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info