554911
2
Zoom out
Zoom in
Previous page
1/2
Next page
JA-60IR Wireless optical barrier MEB52800
2
instant
delay
Figure: 2 The JA-60N transmitter
6. Then power up the TX unit (red mark) by connecting its battery.
7. Press the SYNC TEST button in the TX unit (red mark). The
LED indicator will start flashing to confirm correct positioning of
the sync beam, if not it is necessary to adjust the relative
position of the bars.
8. To test the 3 remaining beams set the DIP switch in the RX unit
to B2 and press the BEAM TEST button. The LED indicator
must be flashing while the button is being pressed, otherwise
adjust the position of the beam B2. Repeat the procedure for
beams B3 and B4.
9. Using the AL DIP switch, set whether the alarm will be triggered
by the interruption of one beam (position 1 – standard false
alarm immunity) or two beams (position 2 – higher false alarm
immunity).
10. Test radio communication between the detector and the
receiving unit by briefly pressing (0.1 sec) the TEST-AL button
which will trigger the detector. To deactivate the detector press
the TEST-AL button again for about 1 second.
11. For correct functioning of the tamper positioned in the bars,
check that the ANTI-STRAPO jumper (see Figure 3) is in the
OFF position. A tamper of the RX unit is reported to the system
as a tamper alarm and a tamper of the TX unit is reported as
activation of the detector (instant or delay zone).
Note: A tamper alarm is activated 1 second after triggering the tamper
switch and it is terminated 10 seconds after its deactivation (during these
10 seconds any other possible activation of the tamper is ignored).
12. Test the function of the detector by interrupting the beams (for
example by stepping between the bars). The speed of the
reaction depends on the number of interrupted beams. After
activation of the detector, the JA-60N transmitter will add an
approximately 1 second delay before the signal is sent to the
receiving unit.
Battery testing and replacement
The detector automatically checks the condition of its batteries. If it is
necessary to replace the batteries, the detector will inform the control
panel about it. If a low battery is indicated the detector works as
normal but, batteries should be replaced as soon as possible (within
a week).
Before replacing the batteries, the control panel must be switched
into mode, which allows detectors opening (User mode or
Programming mode).
Note: Dispose of batteries safely depending on the type of the batteries and
local regulation. Although this product does not contain any harmful
materials we suggest you to return the product to the dealer or directly to
the producer after usage
Maintenance
No special maintenance is needed. The plastic cover can be cleaned
carefully to avoid any mechanical damage by non-abrasive materials.
We recommend regular testing of the JA-60IR along with other
components of the system.
Note: Although this product does not contain any harmful
material we suggest you to return the product to the dealer
or directly to the producer after usage.
RANGE
LOW
HIGH
TEST
Test
B2
Test
B3
Test
B4
ONE
TWO
BEAM
INTERRUPTION
TEST - AL
BEAM TEST B2-B4
BATTERY
RX
unit
white mark
RANGE
LOW
HIGH
TAMPE R
TEST - AL
SYNC TEST
BATTERY
TX
unit
red mark
TAMP ER
TAMP ER
TX
bar
red mark
Leave in
position OFF
A
NTI-STRAPO
Leave in
OPTO posit.
AL
2
1
SYNC
Figure 3
Internet: www.jablotron.cz
Tel.: +420 483 559 999
fax: +420 483 559 993
Pod Skalkou 33
466 01 Jablonec nad Nisou
Czech Republic
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron JA-60IR at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron JA-60IR in the language / languages: English as an attachment in your email.

The manual is 0,08 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info