554977

Jablotron CA-340 Nestor Manual

3
Zoom out
Zoom in
Previous page
1/4
Next page
CA-340 modular car alarm 3/4 VAV50204
Connection without a CAN-Bus converter,
controlling with RC-8x remote controls
Connection pursuant to Fig 1, setting pursuant to profile 1. The values
shown in the table in bold letters are the default ones The profile is defined by
parameter 1 setting.
A description of individual wire functions is available on page 2.
Vehicle status information is obtained via direct connection to the ignition
circuit and door, bonnet and boot switches. A thus connected car alarm can
control the central locking of the vehicle. It is possible to set an extended
locking impulse which can be used to close the windows of certain vehicle
types after arming.
Connection with a CAN-Bus converter,
controlling with RC-8x remote controls
Setting pursuant to profile 1.
Information about the vehicle status (ignition key, door, bonnet, boot) is
obtained via a CAN-Bus converter.
NOTE: The converter cannot be used to control the central locking of the
vehicle.
Direction indicator (flasher) connection
Optical signaling of arming, disarming and alarm is possible in three modes.
Direct connection to the light bulb circuits. Connection pursuant to Fig. 1.
The power supply is directed to the relay contact via a 15A fuse. The contact
output is forked using diodes and it is then connected to the left and right
direction indicator light.
Connection via a warning light switch, pursuant to Fig. 2. When this
option is selected, the INP1 input always has a feedback function (counting
the flashes) and it has to be connected to a direction indicator light power
circuit. It is therefore not possible to use this optical signaling when the alarm
is controlled with the original remote control without using a CAN-Bus
converter (this option is superior to the setting parameter 12 of profile 2, INP1
then has no function for confirmation of disarming or alarm input). The
flashing can then be controlled with the following options:
„switch“ – the relay is switched if the direction indicator lights
should flash
„button“ - the relay gives an impulse to begin and finish flashing
Profile 1 – controls the central locking
parameter
= LED on
= LED off
1
Central lock
control
Yes, ULK and LCK wires control the locks in the
vehicle
(this setting defines the function of parameters
12,13,14)
2
Rearm
Yes
No
3
Autoimo
Yes
No
4
Disarming with the
Valet button
Yes
No
5
Acoustic signaling
Yes
Partial
6
Increased volume
of signaling
Yes
No
7
Open door test
Yes
No
8
Voltage detector
Yes
No
9
Shock warning
Yes
No
10
Shock alarm
Yes
No
11
AUX output
function
EXT detector power
supply
AUX bus output
12
CL input length
0,5 sec
4 sec
13
Extended lock
impulse length
Yes ( 60 sec.)
No (length pursuant
to parameter 12 )
14
DOOR input
activation
Ground
Ground disconnection
15
INP2 input
activation
Ground
Ground disconnection
16
INP2 input
reaction
Alarm
warning
17
18
BLK output
function
Boot
control
Direct
direction
indicator
control
Direction
indicator
control
switch
Direction
indicator
control
button
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Jablotron CA-340 Nestor at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Jablotron CA-340 Nestor in the language / languages: English as an attachment in your email.

The manual is 0,26 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info