578901

Irox PE-DRO Manual

6
Zoom out
Zoom in
Previous page
1/8
Next page
Measuring step length
To determine your step length, proceed as follows:
- Walking: walk 10 steps as you normally would, then measure the distance covered and divide it by ten.
Example:
You measure 6.2 metres. 6.2m / 10 (number of steps) = 0.62m (input step length WALK: 62cm).
- Jogging: here, we recommend that you jog at least 50 steps and then use the distance covered in the
calculation.
Step counter
As soon as you start to walk (see “Important” in Chapter 3!), the steps you take are added and displayed.
The distance, kcal and movement time are counted automatically (see Chapter 4.2/4.4 – 4.6)
Reset (RESET) the measured data
Press and hold the RESET key for at least 4 seconds. All data in the current measurement are then deleted
(Chapter 4.1/4.3 – 4.4: steps, distance, kcal, movement time). You can perform this RESET in all these
functions. However, the data for this deleted measurement are stored in the ODOSTEP and the STEP
TOTAL counter!
Caution: If you perform a RESET in the TOTAL STEP mode (Chapter 4.6), all measurement data, apart
from ODOSTEP, are reset to zero.
4.2 The function STEP (step counter)
As soon as you start to walk (see “Important” in Chapter 3!), the steps you take are added and displayed.
The distance, kcal and movement time are counted automatically (see Chapter 4.2/4.4 – 4.6)
Reset (RESET) the measurement data
Automatically: at midnight, the STEP counter (and the data in 4.4-4.6) is reset to zero.
Manually: press and hold the RESET key for at least 4 seconds. All data for the current measurement are
then deleted (Chapter 4.2 / 4.4– 4.6: steps, distance, kcal, movement time). You can perform this RESET in
all these functions. However, the data for this deleted measurement are stored in STEP TOTAL and
ODOSTEP!
Caution: If you perform a RESET in the TOTAL STEP mode (Chapter 4.6), the measurement data in the
daily memory (STEP) are also reset to zero. The data in ODOSTEP are retained.
4.3 The function ODOSTEP
You can use this function to monitor a training unit with all measurement data.
While you are in the ODOSTEP, you have to start the function by pressing and holding the SET button (hold
for about 4 secs until "ODO" in the top left corner is flashing).
By doing this, you start resp. continue a "training session". You may interrupt the recording by holding the
SET button for about 4 secs again (then ODO stops flashing).
Select the measurement data: with the SET key
You can delete the ODOSTEP separately. Other RESETs (in STEP TOTAL or STEP) do not have any effect
on ODOSTEP.
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Irox PE-DRO at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Irox PE-DRO in the language / languages: English as an attachment in your email.

The manual is 0,27 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Irox PE-DRO

Irox PE-DRO User Manual - German - 8 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info