578936

Irox HBR425i Manual

20
Zoom out
Zoom in
Previous page
1/21
Next page
71 72
7069
6. BELL / ALARM
6a) HOW TO SET AND ARM THE ALARM
To set an alarm,
1. Press [ALARM] once to display alarm time. If the alarm
is disarmed, the time will be displayed as “ OFF ”.
2. Hold [ALARM] for two seconds. The hour digits will
blink.
3. Enter the hour using [ ] or [ ].
4. Press [ALARM]. The minute digits will blink.
5. Enter the minutes using [ ] or [ ].
6. Press [ALARM] to exit.
7. Repeat the same procedure to set single alarm.
The alarm “ ” “ ” and “ Pre-AL” icons will be
displayed indicating which alarm is armed. You can also
arm or disarm an alarm by pressing the [ ] or [ ]
button at alarm display mode. Press [MODE] to return to
clock display mode.
During the setting, press and hold [ ] or [ ] will
increase or decrease the value rapidly.
For display language, you can choose among English (En),
German (DE), French (Fr), Italian (IT) and Spanish (SP) -
in that order. If there is an item you do not wish to change,
simply press [ MODE ] to bypass the item.
When you finished the change, press [ MODE ] to exit.
The display will return to the clock mode.
5e) DISABLE THE RECEPTION OF
THE RADIO CONTROLLED CLOCK
If you are using this product outside the central European
timezone, you may disable the reception of the radio
controlled clock, Press min. 3 Seconds the key [ ] to
disable the automatic time signal reception. The reception
signal [ ] will then disappear from the display.
To re-enable the time signal reception, press again for
min. 3 Seconds the [ ] key.
5b) HOW TO SET THE ZONE TIME
To set the zone time,
1. Press [MODE] until at zone time display mode,
2. Hold [MODE] for two seconds, the zone time offset
will be displayed.
3. Enter the offset using [ ] or [ ].
4. Press [MODE] to exit.
5c) CALENDAR CLOCK DISPLAY MODES
The clock and the calendar share the same section of the
display. The calendar is displayed in a day-month format.
Each press on the [MODE] button will change the display
between clock with second, clock with day of week, zone
time with day of week.zone time with second and
day-month.
5d) HOW TO SET THE CLOCK MANUALLY
To set the clock manually, hold [MODE] for two seconds
it will show the display language. Use [ ] or [ ] to
change it. Press [ MODE ] to confirm. Repeat the same
procedure to set ˚C/˚F, year, month, date, date-month
format, 12/24, hour and minute.
5. RADIO CONTROLLED CLOCK
5a) HOW TO SET THE RADIO
CONTROLLED CLOCK
1. After the batteries are installed. The clock will
automatically search the radio signal. It takes about 3-5
minutes to finish this process.
2. If user wishs to disable the auto-reception feature, hold
the [ ] button for 2 seconds to disable it.
3. To enable the auto-reception feature again, holds the
“Up” for 2 seconds again to force it receive and allow it
receive at desired time.
4. If the radio signal is received, the date & time will be set
automatically with radio control signal icon [ ] turns on.
5. If the clock fails to receive the time signal, it will be show
as [ ] icon. Then user can set the time manually.
W S
6e) ALARM FEATURE
* Weekday Alarm
The alarm sound will be activated and the icon will be
flashed on weekday when it is armed and the alarm time
is reach.
* Single Alarm
The alarm sound will be activated and the icon will be
flashed once when it is armed and the alarm time is
reach. Once it finished, it will be disabled automatically.
* Pre-Alarm
The pre-alarm sound will be activated and the icon
will be flashed if outdoor temperature under or equal
two degree C. Which is programmable 15, 30, 45, 60
or 90 minutes earlier than the weekday alarm or single
alarm time.
7. SPECIFICATIONS
Temperature Measurement
Main unit
Indoor Temperature measurement
Proposed operating range : 0°C to +50.0°C
32.0°F to 122.0°F
Humidity Measuring range : R.H. 10% to 95%
at 25˚C ( 77˚F )
Temperature resolution : 0.1°C
0.2°F
Humidity resolution : 1% R.H.
Remote unit
Proposed operating range : -20°C to + 60°C
-4 °F to 140 °F
Temperature resolution : 0.1°C
0.2°F
RF Transmission Frequency : 433 MHz
Maximum No. of Remote unit : 3
RF Transmission Range : Maximum 30
meters
(open area)
Temperature sensing cycle : around 43~47
seconds
6c) SNOOZE FEATURE
When the alarm sound is on, press the snooze key enter
snooze mode. After 8 minutes, alarm sound will be wake
up automatically. The snooze cycle will be restarted if
you press the snooze key again.
If you leave the alarm sound on for 2 minutes, it will enter
snooze mode automatically with maximum 3 times.
6d) HOW TO STOP AN ALARM
Press [ALARM] on the unit to stop an alarm.
… 20


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Irox HBR425i at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Irox HBR425i in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 4,3 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info