578602
21
Zoom out
Zoom in
Previous page
1/24
Next page
~P.21~
(ENG)
The light will be activated automatically based on an interval which you can define in the following setting
-Place the slide switch in the position AUTO
-Press and hold the key UNIT for 3 seconds
-With the UP or DOWN key you may set the activation interval in steps ( 5,10,20,30 or 60 minutes)
-To confirm the setting, press the UNIT key again
-Now you can define the sequence of light in the crystal by using the UP/DOWN key:
ON=: each icon will be lit for 1 sec, followed by a full illumination of all icons for 2 secs and then the icon
showing the real weather forecast for 10 secs (18 secs if operated with the adapter).
OF=: whenever the display is activated (manually or interval setting),only the icon for the real weather
forecast will be lit for 12 secs
(Note: Above given timings are approximate numbers only)
GETTING STARTED
This Weather Station was designed for easy set up. For best operation, the following steps are required
to be done in the proper sequence.
1. INSERT BATTERIES FOR MAIN UNIT BEFORE DOING SO FOR THE SENSOR UNITS.
2. RECEIVING UNIT CANNOT BE PROGRAMMED MANUALLY UNTIL THE WIRELESS REMOTE SENSOR
UNIT REGISTRATION PROCEDURE HAS BEEN COMPLETED.
3. POSITION THE REMOTE UNIT AND MAIN UNIT WITHIN EFFECTIVE TRANSMISSION RANGE, WHICH,
IN USUAL CIRCUMSTANCES, IS 250 FEET.
Although the remote unit is weather resistant, it should be placed away from direct sunlight, rain or snow.
BATTERY INSTALLATION FOR MAIN UNIT
1. Turn the metal nut anti-clockwise on the bottom of the unit to open and release the battery compartment;
2. Insert 4 AA size 1.5V alkaline battery as indicate by the polarity;
3. Push the battery compartment back, turn the metal nut clockwise to lock;
Note: Replace the batteries when the low battery indicator appears on the top-right corner of the LCD.
WIRELESS REMOTE SENSOR REGISTRATION PROCEDURE
1. Insert x4 AA batteries first to the main unit, the temperature display shows - - . – While the wave icon
will keep blinking for 2 minutes indicate unit is in sensor searching mode.
2. In a second step, insert the x2 AAA batteries for the sensor unit. The LED on the front panel will start
flashing at a rate of one time per around 2 seconds indicates channel-1 is in use.
3. While the LED is flashing, press once the [CH] key will change the sensor channel setting to 2. Keep
toggle on [CH] key can change channel setting up to 5. The LED is blinking at a frequency to indicate
the channel setting. i.e. continuous blinks 2 times indicate channel-2 is selected.
Note: If user does not press any key for 10 seconds, it will exit the channel setting mode and transmit the
RF signal. The main unit will register the temperature reading.
(If the transmitter has the LCD display, the C/F key will toggle the temperature unit on the LCD.) As the
channel 4 & 5 are reserved for other models, please never set the remote sensor to channel 4 & 5.
REMOTE CHANNEL AUTO-SCROLLING
This device is equipped with an auto-scroll function. While the auto-scroll function is set, the unit will
automatically cycle to display the temperature of each remote sensor for 6 seconds.
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Irox EBR808C at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Irox EBR808C in the language / languages: English, German, French, Italian as an attachment in your email.

The manual is 0,6 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Irox EBR808C

Irox EBR808C User Manual - Spanish - 2 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info