161805

Ion lp2cd usb Manual

7
Zoom out
Zoom in
Previous page
1/92
Next page
5
TONEARM SETUP
1. Begin by rotating the counterweight
counter-clockwise until it is in the
complete forward position (NOTE:
this is also the maximum amount of
pressure that can be applied to the
cartridge.)
2. Now there should be a feeling of
weight and resistance when the head
shell is raised and lowered. Begin
rotating the counterweight clockwise
(away from the pivot point) until the
weight and resistance feeling is
gone. If done properly, the tone arm
will pivot with very little resistance
back and forth indicating that there is
exactly 0 grams of stylus pressure.
3. With the counterweight in its new
position further away from tone arm pivot point, grasp the scale ring of the counter weight and rotate it until "0"
is in the vertical position.
4. Finally, rotate the counterweight (and scale ring) counter-clockwise (towards the pivot point) until the desired
amount of weight is reached. If the scale rotates 360 degrees beyond the zero point, the new scale ring reading
should be added to 3.5.
*The included head shell and cartridge assembly requires a minimum of 3 grams and no more than 5 grams for
optimum performance.
Setting the Anti-Skate Adjustment
In most cases, the Anti-Skate should be set to its minimum setting. Anti-Skate compensates for inward tracking forces
that occur with certain cartridges when the stylus nears the center of the record. If the turntable is experiencing
excessive skipping while nearing the center spindle, try increasing the Anti-Skate in the increments indicated on the
dial. Start by adding an increment of 1, test its performance, then increase it more, and so on.
IMPORTANT
Make sure that the felt slipmat is always placed on top of the platter while using the turntable. Failure to use
the slipmat may cause damage to your media as well as damage to the turntable.
Please remove the plastic cartridge cover (needle cover) before operating the turntable.
The tonearm needs to be moved away from resting position (arm clip) for the turntable motor to activate.
PLATTER SETUP
WARNING: Incorrect Platter setup can lead to poor turntable performance, platter instability or permanent motor damage.
1. Start by placing the rubber drive belt around the inner bottom ring of the turntable platter. This should come
preinstalled, but check to make sure that it is not twisted or damaged.
2. Install the platter on the center spindle and press it down firmly. Check to make sure that it rotates uniformly
and does not wobble excessively.
3. Rotate the platter so that the one of the holes is aligned with the Start Stop button on the front corner of the
turntable. The brass motor spindle should be visible through this hole.
4. Reach into the hole and pull the rubber drive belt off of the inner ring, and install it over the motor spindle. Be
careful not to twist the rubber drive belt during this step. Check to make sure the platter rotates uniformly. If the
drive belt is properly installed, there should be a slight amount of tension that brings the platter to a stop after
spinning it freely.
… 7 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ion lp2cd usb at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ion lp2cd usb in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 4,77 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info