519157

Ion ALESIS DM5 Manual

52
Zoom out
Zoom in
Previous page
1/68
Next page
Chapter 6: External Triggering
46 DM5 Reference Manual
Note: Note Chase will not follow any trigger that has been set to Unassigned. To
view an Unassigned trigger’s VU-style bar graph meter in order to adjust gain (page
44), use the [VALUE] knob to select the corresponding trigger input (page 43).
CROSSTALK
If several pads are mounted on one stand or rack it is possible to experience
interaction or “crosstalk” problems. Adjustment of the Xtalk parameter makes it
possible to resolve these problems.
Note: In configurations where some pads are individually mounted, the default
setting of 30 may be sufficient, making it unnecessary to adjust this parameter. In
that case, skip this section and go on to the next section, “Decay”.
With the Xtalk parameter selected (flashing), turn the [VALUE] knob to select the
desired level of crosstalk suppression necessary to stop the problem pad from
triggering (00 is minimum, 99 maximum). This level will depend entirely on your
current pad or drum configuration.
Remember: When experiencing an interaction problem, the trigger that needs
adjustment is the pad that is false triggering, not the pad being struck
. One easy way
to remedy an interaction problem is to “silence” the pad(s) which are not
“false
triggering”.
Example: Suppose you hit the snare pad and the tom 1 pad triggers.
1 First, press [MIX] and reduce the volume of the snare pad to 00. Now when you
hit the snare pad you won’t hear it, but you’ll hear the tom 1 pad false triggering.
2 Next, press the [EXT TRIG] button twice (which gets you to the Xtalk parameter
on page 2) and select the tom 1 trigger to edit.
3 Press the [
] button once to select the Xtalk parameter. While you hit the
snare pad (false triggering the tom pad) gradually raise the crosstalk level of the
tom 1 pad
. Continue to raise the level until the tom pad stops triggering when
you apply hard hits to the snare pad. By using this technique, you have isolated
the problem drum, and made it easy to “dial in” the proper Xtalk value without
the sound from the other drum becoming distracting or confusing.
4 Finally, press [MIX] again and reset the volume of the snare pad to it’s original
level.
Note: Always increase the Xtalk value in small amounts for two reasons. The values
are very sensitive, so an increase of as little as 2 or 3 can make a difference in
suppression. Also, an unnecessarily high Xtalk setting actually suppresses the
sensitivity of the trigger input, resulting in the occasional loss of softer hits.
If a situation where a high Xtalk setting is necessary to stop false triggering, but pad
sensitivity loss is noticeable, try this combination. Start by slightly lowering the Gain
setting for the pad. This should make it possible to lower the Xtalk value, which will
allow the pad sensitivity to increase. With some experimentation and time, you
should be able to find the right combination.
… 52 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ion ALESIS DM5 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ion ALESIS DM5 in the language / languages: English as an attachment in your email.

The manual is 7,25 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info