510488
14
Zoom out
Zoom in
Previous page
1/144
Next page
12
EPG font size
This option allows you to change the size of the text in the EPG, to allow you to see more or less data at once.
Power Up Mode
This option allows you to set the unit to automatically change to a specic mode during power-up. If you select
“Stand-by mode”, the receiver will go into stand-by immediately after power-up. If you select “Last mode”, the
receiver will change to the same mode it was in, prior to switching it off.
Note: The receiver is able to switch on some TV sets that use the “Slow Blanking” signal on the SCART
connector. If “Last Mode” is selected, the receiver and TV will power-up at the same time.
Auto Upgrades
By choosing “Notify”, you will see a
symbol in the upper part of the OSD when a new update is available.
By choosing “Auto” your receiver will be automatically updated while in stand by.
ANTENNA SETTINGS
To set up the receiver for the type of antenna connected, follow the instructions below.
Signal strength and signal quality bars
In two level bar meters, on the right side of the screen,
the user can see the strength and quality of the signal
coming from the antenna dish to the tuners. These
two meters can be used while doing a ne-tuning of
the antenna position. The antenna has to be adjusted
to have maximum possible signal strength and signal
quality.
LNB Type
Select Universal for most standard LNBs, or Unicable if
you have a Unicable LNB.
Motor System
If a motorized dish is connected to the digital receiver,
use this option to set the system used for sending
commands to the motor.
Motorized dish
If you select one of the options for motorized dish and press the “Yellow” function key, a new menu bar will be
open. Here, you are able to adjust and set the position of this satellite. The two level bar meters can be used
during adjustment. Use the color keys on the remote control, as shown at the bottom of the screen, to move the
dish and set the limits.
The “Yellow” “Recalculate” key is used to recalculate
all satellite positions, if the base position of the dish
has been moved. if you move the dish, simply enter
the menu, adjust the position for only one satellite
and press the “Yellow” function key. The receiver will
recalculate all positions accordingly.
Satellite
Use this option to select the satellite for which you
would like to set the position.
Reference transponder
This option allows you to set which transponder is used
as the reference.
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inverto IDL 3290S-CI at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inverto IDL 3290S-CI in the language / languages: German as an attachment in your email.

The manual is 3,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info