790114

Inventum VST400W Manual

14
Zoom out
Zoom in
Previous page
1/32
Next page
assembly instructions
3assembly instructions
3
Before using the fan for the first time, please proceed as follows: carefully unpack the appliance and all components andre-
move all packaging material and any promotional stickers.
Keep the packaging (plastic bags and cardboard) out of reach of children.
After unpacking the appliance, carefully check it for external damage that may have occurred during transport.
Assemble the fan in accordance with the instructions.
1. Start by placing the cross foot at the pedestal. Click the pedestal in the round base of the cross foot - fig. 1.
2. Slide the four cross parts firmly in the round base - fig. 2.
3. When you attach the cross parts correctly, you will hear a click for each part - fig. 3.
4. Loosen the pedestal adjusting nut and pull the tube upwards to the required height. Fasten the pedestal adjustment nut
when the tube is at the required height. Note: if you are unable to see the tube, it is possible that it has fully disappeared
inthe pedestal. Loosen the pedestal adjusting nut and carefully hold the pedestal upside down - fig. 4 and 5.
5. In order to attach the motor part to the pedestal, you must first loosen the wing nut at the bottom of the motor part.
Slidethe motor part on the tube in line with the groove of the tube and tighten the wing nut - fig. 6.
6. Loosen the fastening cap (or take it from the bag) and loosen the lock ring. Attach the rear part of the protective part
onthemotor shaft and fasten it with the lock ring - fig. 7.
7. Place the fan blade on the motor shaft and make sure that the slot of the fan blade properly fits over the pen of the mo-
tor shaft. Fasten the fan blade with the fastening cap - fig. 8.
Test the fan blade by rotating it by hand. When rotating, the blade should not create any friction with the lock ring. If it
does, remove the fan and repeat all steps from the start.
8. Place the front protective guard on the fan and use the clamps to attach it to the rear protective guard - fig. 9.
- Align the front protective guard with the rear protective guard using the positioning clamp on the bottom side
inordertoattach both parts to each other properly. Use the bolt and nut at the top of the guards to attach
theguardstoeach other.
- Press the clamps downwards in order to attach the front and rear protective guards to each other.
9. Place the fan on a flat, stable surface. Clean the exterior of the fan using a slightly damp cloth and then wipe it with
adrycloth.
The fan is ready for use.
Place the pedestal fan on a flat, stable surface. Insert the plug in a socket.
SWITCHING ON/OFF
Press one of the position buttons 1 to 3 to switch on the fan. By pressing position button 0, you switch off the appliance.
Position 0 = off
Position 1 = lowest position
Position 2 = middle position
Position 3 = highest position
OSCILLATION
This fan is able to oscillate (swerve to the left and right) for a better air displacement. Press in or pull out the oscillation knob.
If you want to change the wind to an upward or downward direction, you can simply tilt the fan head upwards or downwards.
ADJUSTING THE HEIGHT OF THE PEDESTAL
In order to adjust the height, loosen the pedestal adjustment nut and move the fan upwards or downwards. Properly hold
on tothe fan when loosening the pedestal adjustment nut, so it cannot drop down unexpectedly. Re-tighten the pedestal
adjustment nut when the fan is at the required height.
operating the pedestal fan
4
14 • English
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum VST400W at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum VST400W in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 9.38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info