694950

Inventum NB560 Manual

11
Zoom out
Zoom in
Previous page
1/28
Next page
using the blender with the glass blender jug
4
English • 11
Before plugging into a socket, check that the voltage in your home corresponds with the voltage printed on the bottom of the
appliance.
1. Place the blender on a flat, clean and dry surface.
2. Make sure that the blender is not activated.
3. Put the ingredients in the glass jug and lock it with the lid.
4. Switch the blender on by selecting a position with the position button.
Attention: Do not activate the mixer constantly, this can cause engine problems. Do not use the mixer for more then 1 minute
continuously, wait 1 minute before you operate it again.
5. When the blender has finished mixing switch the button to off (0) and wait until the blades have stopped turning., before you
remove the glass blender jug.
tips
6
• When the glass blender jug is cracked, do not use the mixer anymore. This could lead to damage while using the mixer.
• To avoid splashes always place the lid on the blender jug.
• Always add liquid ingredients before adding solid ingredients in the mixer.
• The mixer mixes best when you do not add pieces which are too large.
• Always add a half a cup of liquids when you crush ice cubes. Attention: Only crush ice cubes in the glass blender jug.
• To add ingredients while the mixer is activated, take the cap out of the lid and add the ingredients through the opening.
• When the ingredients stick to the sides of the glass jug or are not mixed properly, shut off the engine: wait until the knives have
stopped turning and push the ingredients with a spatula towards the knives.
• To prevent the ingredients from being blend to small, take into account that the mixer mixes in seconds, not minutes!
• Working with warm ingredients can cause a build-up of pressure in the jug and that can cause hot liquids to escape when you take
the lid of the glass jug. Therefore always remove the cap from the lid when you are processing warm ingredients.
using the blender with the to-go bottle
5
Before plugging into a socket, check that the voltage in your home corresponds with the voltage printed on the bottom of the
appliance.
1. Place the blender on a flat, clean and dry surface.
2. Make sure that the blender is not activated.
3. Put the ingredients in the bottle and lock it by firmly turning on the blade set. Turn the drinks bottle around and place it upright on
the motor base unit. Make sure that the  indications are in line and click the bottle tight by turning it slightly to the left.
4. Switch the blender on by selecting a position with the position button. Attention: Do not activate the mixer constantly, this can
cause engine problems. Do not use the mixer for more then 1 minute continuously, wait 1 minute before you operate it again.
5. When the blender has finished mixing switch the button to off (0) and wait until the blades have stopped turning.
6. Click the bottle loose - do not turn too far - and lift it from the motor base unit. Attention: if you turn the bottle too far you turn
the bottle off the blade set and the contents will flow out of the bottle.
7. Turn the drinks bottle around, remove the blade set and firmly turn the lid with drinking spout onto the drinks bottle. You’re ready to
go!
Attention: you cannot crush ice cubes or make warm dishes in the to-go drinks bottle.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum NB560 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum NB560 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,45 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info