704940
29
Zoom out
Zoom in
Previous page
1/44
Next page
Connection with a stable pipework
The cooker comes with a G ½” threaded coupling. The connection to gas supply must be done in a manner that excludes stresses in
any point of the pipework or parts of the appliance. Make sure you do not exceed the torque when making the connection (maximum
torque is 20 Nm). Otherwise, the connection may be faulty or leaks may occur.
The gas hose should not touch metal elements of the cooker back shield.
Important! Each time you replace a reducer, carry out technical inspection of the cooker that covers gas valves and proper
operation of the flame failure cut-off device.
Caution! On completion of the cooker installation, the tightness of all connections should be checked, e.g. applying water with
soap. Do not use fire to check tightness.
ELECTRICAL CONNECTION
ADAPTING THE COOKER TO ANOTHER TYPE OF GAS
This operation may only be carried out by an appropriately authorised fitter.
If the gas the cooker is to be supplied with differs from the gas provided for the cooker by the manufacturer, that is G20 / 25 mbar,
burner nozzles must be exchanged and the flame needs to be adjusted.
In order to adapt the cooker to burn a different type of gas, you should:
exchange the nozzles (see the gas tables below);
adjust the “economical” flame.
Caution! The cookers provided by the manufacturer have burners which are factory-adapted to use the gas specified on their rating
labels.
Gas table
Burner flame Re-arming from liquid gas to natural gas Re-arming from natural gas to liquid gas
Full
1. Exchange a burner nozzle for the appropriate
type according to the gas table.
1. Exchange a burner nozzle for the appropriate
type according to the gas table.
Economical
2. Unscrew an adjusting bolt slightly and adjust
the flame size.
2. Screw in an adjusting bolt slightly and check
the flame size.
In order to perfom adjusting operations, take off the knobs.
Surface burners applied do not require adjustment of primary air. A correct flame has distinct internal cones of blue and green colour.
A short, humming flame or long, yellow and smoking one, without clearly outlined cones, shows improper quality of gas in the house-
hold piping or a damaged or soiled burner. In order to check a flame, heat a burner for around 10 minutes with a full flame, and next
turn the valve knob to the economical flame position. The flame should not go out or jump onto the nozzles.
The cooker is manufactured to work with a one-phase alternating current (230V 1N~50Hz) and is equipped with a 3 x
1,5 mm
2
connection lead of 1.5 m length with a plug including a protection contact.
A connection socket for electricity supply should be equipped with a protection pin and may not be located above the
cooker. After the cooker is positioned, it is necessary to make the connection socket accessible to the user.
Before connecting the cooker to the socket, check if:
- the fuse and electricity supply are able to withstand the cooker load,
- the electricity supply is equipped with an efficacious ground system which meets the requirements of current
standards and
provisions.
- the plug is within easy reach.
English 29
G25.3/25 mbar* G20/20 mbar G30/30 mbar
SOMIPRESS burners
Injector
diameter
Injector mark
Injector
diameter
Injector mark
Injector
diameter
Injector mark
1 0.70 mm 71 0.72 mm 72 0.52 mm 52 1 Simmer burner 1.0 kW
2 0.98 mm 98 0.98 mm 98 0.67 mm 67 2 Semi-rapid burners 1.8 kW
3 1.17 mm 116 1.17 mm 117 0.83 mm 83 1 Rapid burner 2.8 kW
29


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum LK010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum LK010 in the language / languages: English, Dutch as an attachment in your email.

The manual is 4,38 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Inventum LK010

Inventum LK010 User Manual - German, French - 44 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info