551598

Inventum IKV1781S Manual

23
Zoom out
Zoom in
Previous page
1/32
Next page
troubleshooting
7
If your appliance is not working properly, it may be a minor problem, therefore check the following:
Problem Cause Solution
Appliance is not functioning; light
does not work
- Appliance is not plugged in
- There is a power failure
- The thermostat is set on ●
- Plug the appliance in
- Check the fuse box
- Set the thermostat on setting 1-5
Temperature inside the
refrigerator is too high or too low
Thermostat has been set
incorrectly
Set the thermostat correctly
Air circulation vents are blocked Clean the ventilation openings
Water is running out of the
refrigerator
Drain outlet is blocked Clear the drain outlet with a skewer
Appliance is excessively noisy Has the appliance been installed
correctly?
Check the installation
Are the pipes at the back touch-
ing or vibrating?
Check it and move the appliance forwards
The inside light is not working Lamp is defective Replace the bulb following the instructions
Note: gurgling and hissing noises due to expansion in the refrigerant circuit are normal.
English • 23
installation instructions
8
Before installation, read the instructions carefully.
• Fit the refrigerator/freezer in stable kitchen units only with sufficient ventilation (figure B and C).
• If necessary, reverse the door according to the instructions.
• Check the installation dimensions according to figure C. The position of the joint between the unit doors must be level with the
position of the joint between the appliance doors.
1 See figure A for the necessary attachment components.
2 Insert the trim flap
1
into the slot and screw by screws
6
(figure D).
3 Pass the power cord through the ventilation shaft and position it so that the appliance could be easily plugged in once it has
been installed (figure B and C).
4 Take out the trim gasket
2
located on the side panel of the appliance and stick it on the reverse side of the door hinges of the
appliance (figure E).
5 Raise the appliance and slide into the kitchen unit. Push the appliance to the reverse side of the door hinges providing that the
trim gasket
2
covers the space between the appliance and the kitchen unit.
6 Allign the front feet with the front surface of the kitchen unit (figure F).
7 Screw the front feet by using screws
5
(figure F).
8 Screw the trim flap
1
to the kitchen unit using screws
5
(figure G).
9 Screw the fixing bracket 11, as leaned to the kitchen unit by using screws
5
. Repeat this for the opposite side (figure H).
10 Screw the guides
3
to the appliance doors with screws
6
. Lean the appliance doors to the unit door as it is opened at the right
angle 90°. Slide the rails
4
into the guides
3
aligning the groove. Screw the rails
4
to the unit doors with screws
5
(figure J).
11 Set 1-2 mm gap on the handle side between the unit itself and the unit doors by adjusting the guides
3
(figure J). That is vital for
the appliances performance.
IKV1781S-instructions.indd 23 27-8-2014 9:49:40
… 23 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum IKV1781S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum IKV1781S in the language / languages: English, Dutch as an attachment in your email.

The manual is 3,15 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info