705017

Inventum IKG9022WG Manual

20
Zoom out
Zoom in
Previous page
1/28
Next page
faults
7
If the hob does not function properly, according to you, please try to solve the problem first by checking the points in the table below
before contacting the customer department.
Fault Possible cause Solution
There is a smell of gas near
the hob.
The hob connection is leaking. Turn off the main gas supply valve. Contact your
installer.
A burner does not ignite. • The plug is not in the socket.
• A fuse is defective/ or switched off
in the fuse box.
• Ignition is dirty/damp.
• The burner parts are not placed
correctly.
• The burner parts are dirty/damp.
• The main gas suplly valve is closed.
• A fault in the gas mains.
• Wrong type of gas used.
• Put the plug into the socket.
• Replace the fuse or switch on the fuse in the fuse
box.
• Clean/dry the ignition.
• Refit the burner and watch the openings for the
thermocouple and the ignition.
• Clean/dry the burner parts.
• Open the main gas valve.
• Consult your gas supplier.
• Check whether the gas used is suitable for the
appliance. Contact your installer if it is not correct.
The burner extinguishes
immediately after igniting.
• The control knob has not been
pressed long and/or deep enough
(at least 3 seconds).
• The thermocouple is dirty.
• Keep the control knob fully pressed for at least 3
seconds between the highest and the lowest flame
setting. This can take longer the first time because of
the gas supply.
• Clean/dry the thermocouple.
The burner does not burn
evenly.
• The burner parts are not placed
correctly.
• The burner parts are dirty/damp.
• The wrong type of gas is used.
• Refit the burner and watch the openings for the
thermocouple and the ignition.
• Clean/ dry the burner parts.
• Check whether the gas used is suitable for the
appliance. Contact your installer if it is not correct.
cleaning & maintenance
6
Clean the hob after each use to maintain it in good condition. Food residue can create stubborn stains if not removed directly after
use.
Use a mild cleaning detergent to clean the hob. Burner parts and the pan supports should not be cleaned in the dishwasher. The
dishwasher detergent can corrode the materials.
The pan supports, burners and burner caps are removable for easy cleaning of the hob.
• First clean the control knobs, burners, burner caps and pan supports.
• Check whether the thermocouple and ignition are clean. If necessary use a toothpick or needle.
• Clean the drip tray.
• Clean everything again with just a damp cloth and dry it thoroughly.
• Refit the burners. Make sure the openings are aligned for the thermocouple and the ignition.
• Refit the burner caps.
• Refit the pan supports. Place them carefully on the drip tray without sliding.
PERSISTENT STAINS
Persistent stains on the pan supports and burner caps can best be removed with a fluid detergent or a plastic scouring sponge. Never
use aggressive cleaning products or sharp objects to clean the hob.
Persistent stains on stainless steel are best removed with a special stainless steel cleaning product. Always wipe in the direction of the
grain to prevent damage to the protective layer.
The surface of the stainless steel drip tray can discolour slightly over time.
20 • English
IKGxxxx-instructions.indd 20 15-12-2014 12:01:28
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum IKG9022WG at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum IKG9022WG in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,41 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info