616206
23
Zoom out
Zoom in
Previous page
1/28
Next page
ELECTRICAL CONNECTION
Check that the voltage in your home corresponds with the voltage printed on the bottom of the appliance.
The earthing of the appliance is compulsory by law.
Attention: the connection point must always be accessible.
THE FITTING OF THE APPLIANCE
Check that the cabinet and the cut-out meet the dimension and ventilation requirements.
Remove the chips from the cutting job in the opening of the worktop and treat the saw ends of wooden or synthetic worktops with
sealing varnish if necessary, to prevent moisture causing the worktop to swell.
Remove the protective layer from the sealing tape and apply the tape on the edge of the cut out on the worktop. . Do not stick the
tape around the corners, but cut 4 separate pieces to seal the corners well.
Fit the supllied mounting brackets on the appliance.
Lay the hob in the recess.
Tighten the screws of the mounting brackets to firmly fit the hob in the cut-out.
Connect the appliance to the electrical mains and the gas mains. The appliance is ready for use.
Check that it works properly.
REMOVING THE HOB
Disconnect the hob from the electrical mains and the gas mains and loosen the screws of the mounting brackets. Remove the hob by
pushing it upwards from the bottom. Attention! Beware of damage to the appliance! Do not try to remove it from the top.
GAS CONNECTION
The connection of the hob to the gas pipe network must be made by means of a special gas hose or a stainless steel
hose with a continuous-surface complying with local regulations.
Always a stainless steel hose when placing the hob above an oven. Attention: the stainless steel hose must hang
freely. It must not be able to touch any moving parts of the cabinet.
Check the perfect sealing after installation using a soapy solution.
G25/25 mbar*
(kW)
1 1,0 1 Simmer burner
2 1,75 2 Semi-rapid burner
3 3,0 3 Rapid burner
4 3,5 4 Wok burner
* Check with the service organisation of Inventum if you want to adjust the appliance for different types of gas. Find the
method in the manual of the conversion kit.
English 23
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum IKG6020 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum IKG6020 in the language / languages: English, Dutch as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info