695048

Inventum HNK247 Manual

14
Zoom out
Zoom in
Previous page
1/32
Next page
cleaning & maintenance
5
4.4 Setting the temperature
Setting 0: OFF
Setting 1: minimum heat
Setting 2: medium heat
Setting 3: maximum heat
CAUTION
If the heating pad is being used over several hours it is
recommended to set the lowest temperature setting (1) on the
controller to avoid overheating the heated body part, which may
lead to burns to the skin.
4.6 Switching off
To switch the heating pad off, set the sliding switch for ON/OFF to setting 0 (OFF) position. The temperature settings are then no
longer illuminated.
WARNING
Before cleaning, always remove the mains plug from the socket first. Then disconnect the controller from the heating pad by
unplugging the plug-in coupling. Otherwise there is a risk of electric shock.
CAUTION
• The controller must never come into contact with water or other liquids. Otherwise, the controller may be damaged.
To clean the controller, use a dry, lint-free cloth. Do not use any chemical or abrasive cleaning agents.
Small marks on the heating pad can be removed with a damp cloth or sponge, or if necessary, with a little liquid detergent for delicate
laundry.
14 • English
NOTE
If the heating pad is not in use, switch the side sliding switch for ON/OFF and temperature settings to the OFF (0) position
and remove the mains plug from the socket. Then disconnect the controller from the heating pad by unplugging the plug-in
coupling.
NOTE
The fastest way to warm up the heating pad is to initially set the highest temperature setting of the controller, first.
NOTE
This heating pad has a turbo function, which allows the heating pad to warm up faster in the first 10 minutes.
4.5 Automatic switch-off
This heating pad is equipped with an automatic switch-off function. This turns off the heat supply approx. 90 minutes
after the initial use of the heating pad. The temperature setting display then starts to flash. So that the heating pad can
be switched back on, the sliding switch for ON/OFF and temperature settings must first be set to setting 0 (OFF). After
about 5 seconds it is possible to switch it on again.
4.3 Switching on
To switch the heating pad on, set the sliding switch for ON/OFF and temperature settings to setting 1, 2 or 3. The temperature setting
is illuminated when switched on.
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum HNK247 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum HNK247 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,8 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info