Manual Inventum BM20 BLOOD PRESSURE MONITOR (page 28 of 32) (English, German, Dutch, French)

656785

Zoom out

Zoom in

1/32

Measuring your blood pressure

• Put the cuff on as described above and take up the position in which you wish to perform the measurement.

• Switch on the device with the Start/Stop-button.

• A self-test runs, during which all display elements are illuminated briefly, and then the measurement starts.

While the cuff is being pumped up, the symbol ▲ is displayed. Pressure is increased to 180 mmHg. If this

pressure is not sufficient, the device automatically pumps another 30 mmHg (fuzzy logic).

• When the pressure in the cuff is slowly released and the pulse is recorded, the symbol appears.

• Once measurement has ended, residual air pressure is released very quickly and the symbol ▼appears.

Pulse, systolic and diastolic pressures are displayed.

• Now press memory keys “M1” or “M2” to select the required user memory. If you do not select any user

memory, the measurement result is assigned for storage in the user memory which was last used. The

symbol “M1” or “M2” appears accordingly in the display.

• Switch off the blood pressure monitor with the Start/Stop button. The measurement result is then saved to

the selected user memory. If you forget to switch off the device, it switches off automatically after approx. 3

minutes. Even then, the result is still saved to the selected user memory.

Wait at least 5 minutes before any new measurement!

Displays of the readings saved

The computer automatically saves the blood pressure readings of the last 30 measurements. When the

30 memory locations are exceeded, the current oldest value is deleted. You can recall stored results from the

two user memories and display averages.

• Press memory buttons “M1” or “M2”. First the average is displayed of all the results held in this user

memory. This is indicated by reading ‘A’.

• Continue pressing the memory button to recall other individual measurement results - the first result to

appear is that of the most recent value measured. These individual values are indicated by memory location

numbers 1 to 30. After approx. 4 seconds, the date of the respective measurement result is displayed

and then the time after a further 4 seconds.

• Once 30 individual values are in the memory, the oldest value is deleted in order to make room for the

new measured value.

• Switch off the device using the Start/Stop button or else the device will switch off automatically after approx.

30 seconds.

Note: You can also use the two user memories to save measurement results separately, e.g. in the morning

and evening.

Deleting saved values

You can delete saved values individually or else you can delete all of them.

• To delete individual values, first select the stored value you wish to delete and keep memory button “M1”

or “M2” depressed. The display starts blinking. Keep holding the button depressed until the display has

completely cleared.

• To delete an entire user memory, you have to select the appropriate user memory. The average is displayed

and indicated with ‘A’. Hold the memory button “M1” or “M2” depressed until the display starts blinking

and keep the button depressed until the display completely clears.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Inventum BM20 BLOOD PRESSURE MONITOR in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,66 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Inventum BM20 BLOOD PRESSURE MONITOR Manual

Product: