Manual Inventum BM 120 (page 17 of 48) (English, German, Dutch, French)

504091

Zoom out

Zoom in

1/48

1: Normal This program is mostly used for baking a

white bread.

2: French The bakingtime with this program is

longer than with the normal program

which gives the bread a harder crust.

3: Whole wheat This program is used for preparing bread

made from heavier ﬂours, such as whole

wheat-, wheat- and multi-grainbread.

These ﬂours need more time kneading

and rising. The bread will generally be

smaller because the ﬂour is heavier.

4: Cake For preparing a bread made with

bakingpowder instead of yeast. Breads

made with this program will be less high

and more compact. The timer cannot be

used with this program because of the

immediate activity of the bakingpowder.

If you want to make cake with this

program we advise you to put all the

ingredients in the breadpan. Select the

program and before you press start, stir

the ingredients with a wooden spoon.

This increases the kneading.

5: Quick You can use this program for baking a

white bread in short amount of time.

The bread will be smaller then a bread

baked with the normal program.

6: Sweet For preparing “sweet“ breads like bread

with raisins and nuts.

7: Dough With this program you can make dough

for buns, pizza or any other recipe with

needs dough. The dough will not be

baked. A signal sounds, indicating that

the dough is ready and can be removed

from the breadpan.

8: Jam For preparing a delicious jam. Note:

Make sure that you remove all the pips

before you put the ingredients in the

breadpan. Sharp pips can damage the

non-stickcoating. Process: Put all the

ingredients in a breadpan and select

the JAM program. Press Start and the

breadmaker will ﬁrst heat up the

When, after switching on the breadmaker, the display says

“H:HH”, it means that the temperature of the breadmaker

is still too high. Open the lid and leave the breadmaker

to cool down before you bake another bread. When the

display says EE0 or EE1, unplug the breadmaker and

contact the service department. The temperature sensor

might be failing.

Menu-button

Press this button to select one of the automatic

programs available. These settings are listed on the last

page of this manual. Every time you press this button

you will hear a beep and the number of the program

changes. The program is shown on the display. This

breadmaker has 12 programs (see: Programs).

Light-button

This button activates the lighting in the breadmaker. The

light will stay on for 1 minute.

Color-button

Press the color-button to select one of the three crust

colour settings available for the bread settings only; light,

medium or dark.

TIP: If you try a recipe for the ﬁrst time, we advise you

use crust colour medium.

Timer

For use when setting the timer to delay baking. By

pressing the button, the time will move up in 10 minutes

increments to preset the programmable timer. See: How

to use the preset timer.

Cycle-button

This button allows you to adjust the time for each step

of the program. Kneading, rising, baking and keep warm

to make a personalized style bread.

Gram-button

You use this button to select the size of bread you wish

to make. You can choose a bread of 900 or 1150 grams.

TIP: The total amount of ingredients listed in the recipe,

is the size/ weight of the bread you are going to make.

Pause-button

After you have started the program, you can press PAUSE

to interrupt the program at any time. The machine

will be paused, but the setting will be memorized. The

remaining time will be ﬂashing on the LCD. Press PAUSE

again and the machine will continue the program. the

machine will automatically resume the program after 10

minutes.

TIP: Only use this button while the machine is kneading.

Start- and stopbutton

With this button you can either start or stop the program.

TIP: If you have chosen the wrong program, you can

alter this by pressing the stop-button for a few seconds.

You can reset the breadmaker with the correct program.

START: to start a program, press the button and you will

hear a beep. The colon in the time on the display will

blink and the time starts to countdown.

STOP: to stop a program, press the button for a few

seconds until you hear a beep. The sound conﬁrms that

you have stopped the program.

5 | THE DISPLAY

7 | PROGRAMS

6 | ERRORS IN THE DISPLAY

etc.). If added before this stage, excessive kneading will

cause the ingredients to break down, rather than hold

their shape. Be careful not to use ingredients which are

too big and too hard. They can cause damage to the

non-stickcoating.

ON/OFF

How to check if the

machine is working or if

the program is running?

If the colon blinks, the

program is running.

If the colon is steady, the

program has stopped.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Inventum BM 120 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 8,3 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Inventum BM 120 Manual

Product: