790057

Inventum AKV6004 RVS Manual

24
Zoom out
Zoom in
Previous page
1/52
Next page
24 • English
65
INSTALLATION OF THE COOKER HOOD
The installation of the cooker hood on a discharge to the outside and a cooker hood with recirculation is identical.
1 Remove the fat filters.
Place the cooker hood at the required position at a minimum height of 65 cm above the cooking section and mark the bottom
side of the cooker hood on the wall/side wall. Determine the centre of the cooker hood.
Determine the centre of the cooking section and mark this point at the height of the cooker hood. This is to be able to position
the cooker hood centrally above the cooking section.
A = full width: 562 mm
B = full height: 187 mm
C = diameter discharge opening: Ø 150 mm.
2 Determine the position of the air discharge tube. Limit the number of bends and unnecessary lengths in the discharge tube.
As a result, the cooker hood will function better.
Saw out the holes for the discharge tube. The discharge opening (C) has a diameter of 150 mm. The hole for the discharge tube
must be 10 mm larger than the discharge tube.
3 Attach the discharge tube on the upper side of the discharge channel and allow it to hang down.
4 See how you want to mount the cooker hood - 4a, 4b or 4c.
4a The cooker hood can be attached via holes in the side of the base unit, by means of screws in the kitchen cabinet.
4b The cooker hood can be attached via holes in the rear wall of the base unit, by means of screws through the kitchen cabinet into
the wall.
4c The cooker hood can be attached via holes in the top side of the base unit, by means of screws in the kitchen cabinet.
Remove the cooker hood and pre-drill the holes. Use a drill with a 8 mm diameter. Drill the hole approximately 45 mm deep.
5 Place the cooker hood back in the kitchen cabinet. When the discharge channel is no longer within reach, you must connect the
discharge tube to the cooker hood before you fully place the cooker hood in the kitchen cabinet.
Now fasten the cooker hood to the kitchen cabinet using the supplied screws.
6 Place the fat filters back.
Remove all protective film prior to using the cooker hood.
ELECTRICAL CONNECTION
Check that the voltage corresponds with what is stated on the information plate. Insert the plug into the socket. The cooker hood is
equipped with a connection plug. Install the cooker hood in such a way that the plug is always within reach. Preferably place the wall
socket out of sight, such as behind the discharge channel.
Caution: If you want to create a permanent connection, make sure an omnipolar switch with a contact distance of at least 3 mm
isinstalled in the supply line.
… 24 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum AKV6004 RVS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum AKV6004 RVS in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 2.1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info