551576
21
Zoom out
Zoom in
Previous page
1/28
Next page
MOUNTING AGAINST THE WALL
Attention: the cooker hood should be mounted onto a flat perpendicular kitchen wall.
Use the provided screws and plugs for mounting against the wall.
Measure the right height for the cooker hood (min. 65/75 cm) and mark the underside of the cooker hood on the wall.
Open the glass visor gently by pulling it towards you.
Remove the grease filters to expose the interior of the cooker hood. A keyhole slot (A) and a retainer hole (B) will be visible on
either side of the back panel.
Hold the cooker hood level against the wall on the correct height according to the marking and mark the holes (A+B) on the wall.
Drill the holes with a masonry drill off Ø8mm at the top of each marked slot and push in a rawl plug in each hole.
Partly insert two screws in the plugs, with a head diameter slightly smaller than the lower opening in the keyhole slot. Leave
about 5 mm of the screw sticking out.
Lift the cooker hood and slide the keyhole slots over the two screws.
Mark the two lower retainer holes and lift the cooker hood down.
Drill the holes with a masonry drill of Ø8mm and insert the plugs.
Mount the cooker hood and place the screws in the retainer holes. Tighten all four screws.
Replace the grease filters.
Place an exhaust-air pipe when you have chosen a duct as the extraction system.
Plug in the appliance.
MOUNTING BELOW A KITCHEN CUPBOARD
Attention: if the cooker hood it to be mounted underneath a cupboard, also take the minimum height (min. 65/75 cm) into
account. Use the provided bolts, nuts and washers for mounting underneath the cupboard.
Advice: Use the provided drilling template to mark the necessary holes for the bolts and for the hole of the exhaust when
connecting the cooker hood to a duct.
Open the glass visor by pulling it gently towards you.
Remove the grease filters to expose the interior of the cooker hood.
Hold the cooker hood underneath the cupboard and mark the four retainer holes (B) and mounting aid holes (A) at the bottom
of the cupboard.
Tape the drilling template to the bottom of the cupboard aligned with the marked positions and draw the hole for the power
cord and the exhaust pipe (C).
ø 120
90
545
35
225
112,5
42
16
70
ø 120
543
260
92
150
A A
B B
C
ø 120
90
545
35
225
112,5
42
16
70
ø 120
543
260
92
150
A A
B B
C
B B
English 21
AKO6001-AKO6002-instructions.indd 21 27-8-2014 11:16:44
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventum AKO6002 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventum AKO6002 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,14 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info