Manual Inventum AC907W (page 34 of 100) (English, German, Dutch, French)

790072

Zoom out

Zoom in

1/100

- Marking to the equipment continues to be visible and legible. Markings and signs

that are illegible shall be corrected;

- Refrigeration pipe or components are installed in a position where they are

unlikely to be exposed to any substance which may corrode refrigerant containing

components, unless the components are constructed of materials which are

inherently resistant to being corroded or are suitably protected against being so

corroded.

9) Checks to electrical devices

Repair and maintenance to electrical components shall include initial safety checks

and component inspection procedures. If a fault exists that could compromise safety,

then no electrical supply shall be connected to the circuit until it is satisfactorily dealt

with. If the fault cannot be corrected immediately but it is necessary to continue

operation, an adequate temporary solution shall be used. This shall be reported to the

owner of the equipment so all parties are advised.

Initial safety checks shall include:

• That capacitors are discharged: this shall be done in a safe manner to avoid

possibility of sparking;

• That there no live electrical components and wiring are exposed while charging,

recovering or purging the system;

• That there is continuity of earth bonding.

7. Repairs to sealed components (Annex DD.4)

1) During repairs to sealed components, all electrical supplies shall be disconnected

from the equipment being worked upon prior to any removal of sealed covers,

etc. If it isabsolutely necessary to have an electrical supply to equipment during

servicing, then a permanently operating form of leak detection shall be located at

the most critical point to warn of a potentially hazardous situation.

2) Particular attention shall be paid to the following to ensure that by working on

electrical components, the casing is not altered in such a way that the level of

protection is affected.

This shall include damage to cables, excessive number of connections, terminals

not made to original speciﬁcation, damage to seals, incorrect ﬁtting of glands, etc.

Ensure that apparatus is mounted securely.

Ensure that seals or sealing materials have not degraded such that they no

longer serve the purpose of preventing the ingress of ﬂammable atmospheres.

Replacement parts shall be in accordance with the manufacturer’s speciﬁcations.

NOTE: The use of silicon sealant may inhibit the effectiveness of some types

of leak detection equipment. Intrinsically safe components do not have to be

isolated prior to working on them.

8. Repair to intrinsically safe components (Annex DD.5)

Do not apply any permanent inductive or capacitance loads to the circuit without

ensuring that this will not exceed the permissible voltage and current permitted for the

equipment in use.

Intrinsically safe components are the only types that can be worked on while live in the

presence of a ﬂammable atmosphere. The test apparatus shall be at the correct rating.

34 • English

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Inventum AC907W in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 16.8 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Inventum AC907W Manual

Product: