771742
5
Zoom out
Zoom in
Previous page
1/30
Next page
4
1-1 Indoor Unit
1-2 Outdoor Unit
Ensure the spaces indicated by arrows from the wall, ceiling, fence or other obstacles.
There should not be any heat source or steam near the unit.
There should not be any obstacles blocking the air circulation.
A place where air circulation in the room is good.
A place where drainage can be easily done.
Do not install the unit near the door way.
There should not be any direct sunlight. Otherwise, the sun will fade the plastic cabinet and affect
its appearance. If unavoidable, sunlight prevention should be taken into consideration.
( wall or obstacle )
4cm
(min)
>30(cm)
(min)
50cm(min) 50cm(min)
Front
>200cm
Rear
5cm
(min)
(1) Please stand the unit in hard and flat ground;
Please reserve space for installation and maintenance.
(1) Before installing the outdoor unit, you should:
If an awning is built over the unit to prevent direct sunlight or rain, be careful that heat radiation from
the condenser is not obstructed.
Select a place that is easy to connect indoor unit's pipe and electric wires.
Avoid a place where combustible gas may leak or stay.
Pay attention that water may drain out of the outdoor unit while in "Heat" mode.
Ensure the enough space around the back and sides and the front of the unit.
Take the air conditioner weight into account and select a place where noise and vibration are
minimum.
(2) Please check the elevation difference between the indoor unit and the outdoor unit, the length of the
refrigerant pipe, and the curved places (bend) of the pipe are no more than the following numbers:
Elevation difference: no more than 10 M (if the elevation difference between indoor and outdoor unit
is more than 10 meters, it is recommended that the outdoor unit be located
higher than the indoor unit.)
Pipe length: no more than 20 M
Bends: no more than 3 places
( Ceiling)
The outdoor unit should be put in a position that guarantees the minimum space for sufficient air
circulation and to allow maintenance work and the connections of electrical and refrigerant circuit lines.
It may be installed on a floor or flat roof or wall-mounted, provided its weight is properly supported and
there is no transmission of vibration to the adjacent rooms.
Selecting installation place
INSTALLATION INSTRUCTIONS
5


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventor V4MFI-66B at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventor V4MFI-66B in the language / languages: English as an attachment in your email.

The manual is 4.17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Inventor V4MFI-66B

Inventor V4MFI-66B User Manual - English - 52 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info