771590
13
Zoom out
Zoom in
Previous page
1/156
Next page
Page 12
Refer to the following diagram to ensure proper distance from walls and ceiling:
Step 2: Attach mounting plate to wall
The mounting plate is the device on which you
will mount the indoor unit.
1.
Remove the screw that attaches the mounting
plate to the back of the indoor unit.
2.
Place the mounting plate against the wall
in a location that meets the standards in
the Select Installation Location step. (See
Mounting Plate Dimensions for detailed
information on mounting plate sizes.)
3.
Drill holes for mounting screws in places that:
have studs and can support the weight of
the unit
correspond to screw holes in the mounting
plate
4.
Secure the mounting plate to the wall with
the screws provided.
5.
Make sure that mounting plate is flat against
the wall.
NOTE FOR CONCRETE OR BRICK WALLS:
If the wall is made of brick, concrete, or similar
material, drill 5mm-diameter (0.2in-diameter)
holes in the wall and insert the sleeve anchors
provided. Then secure the mounting plate to
the wall by tightening the screws directly into
the clip anchors.
Step 3: Drill wall hole for connective piping
You must drill a hole in the wall for refrigerant
piping, the drainage pipe, and the signal cable
that will connect the indoor and outdoor units.
Fig. 3.1-b
12cm (4.75in)
or more
2.3m (90.55in) or more
12cm (4.75in)
or more
15cm (5.9in) or more
1.
Determine the location of the wall hole based
on the position of the mounting plate. Refer
to Mounting Plate Dimensions on the
next page to help you determine the optimal
position. The wall hole should have a 65mm
(2.5in) diameter at least, and at a slightly
lower angle to facilitate drainage.
CAUTION
When drilling the wall hole, make sure to
avoid wires, plumbing, and other sensitive
components.
2.
Using a 65mm (2.5in) or 90mm(3.54in)
(depending on models )core drill, drill a
hole in the wall. Make sure that the hole
is drilled at
a slight downward angle, so
that the outdoor end of the hole is lower
than the indoor end by about 5mm to 7mm
(0.2-0.275in). This will ensure proper water
drainage. (See Fig. 3.2)
3.
Place the protective wall cuff in the hole. This
protects the edges of the hole and will help
seal it when you finish the installation process.
Page 13
Wall
Indoor Outdoor
mm7-5
(0.2-0.275in)
Fig.3.2
MOUNTING PLATE DIMENSIONS
Different models have different mounting plates.
In order to ensure that you have ample room to
mount the indoor unit, the diagrams to the right
show different types of mounting plates along
with the following dimensions:
Width of mounting plate
Height of mounting plate
Width of indoor unit relative to plate
Height of indoor unit relative to plate
Recommended position of wall hole (both
to the left and right of mounting plate)
Relative distances between screw holes
Fig. 3.2
Model B
Model D
302mm(11.9in)
805mm(31.7in)
1106mm(43.5in)
599mm(23.6in)
342mm(13.5in)
Model C
964mm(37.9in)
482mm(19in)
325mm(12.8in)
406.4mm(16in)
452.7mm(17.8in)
249mm(9.8in)
153mm(6in)102mm(4in)
39mm(1.5in)
pipe hole
φ65mm
2.56 in
pipe hole
φ65mm
2.56 in
pipe hole
φ65mm
2.56 in
pipe hole
φ65mm
2.56 in
pipe hole
φ65mm
2.56 in
pipe hole
φ65mm
2.56 in
Indoor unit outline
54mm(2.1in)
Model A
717mm(28.2in)
302mm(11.9in)
318mm(12.5in)
409mm(16.1in)
249mm(9.8in)
153mm(6in)102mm(4in)
39mm(1.5in)
pipe hole
φ65mm
2.56 in
pipe hole
φ65mm
2.56 in
Indoor unit outline
54mm(2.1in)
71mm(2.80in)
132mm
(5.20in)
219mm(8.62in)
262mm(10.31in)439mm(17.28in)
Indoor unit outline
Indoor unit outline
174mm
(6.85in)
320mm(12.60in)
130mm
(5.12in)
55mm(2.17in)
558mm(21.97in)
Correct orientation of Mounting Plate
Φ
NOTE: When the gas side connective pipe is
16mm(5/8in) or more, the wall hole should
be 90mm(3.54in).
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Inventor P9VO32 Passion Eco at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Inventor P9VO32 Passion Eco in the language / languages: English, German as an attachment in your email.

The manual is 25.36 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Inventor P9VO32 Passion Eco

Inventor P9VO32 Passion Eco Additional guide - English - 24 pages

Inventor P9VO32 Passion Eco Additional guide - English - 60 pages

Inventor P9VO32 Passion Eco User Manual - English - 76 pages

Inventor P9VO32 Passion Eco Additional guide - German - 60 pages

Inventor P9VO32 Passion Eco User Manual - German - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info