686152

Intex ZS8110 Krystal Clear Manual

20
Zoom out
Zoom in
Previous page
1/23
Next page
(187PO) MODEL ZS8110 OZONE & SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 05/09/2016
187
PO
SAVE THESE INSTRUCTIONS
English
Page 20
TROUBLESHOOTING GUIDE
INSUFFICIENT
CHLORINE
WHITEFLAKESIN
THE WATER
NOLEDDISPLAY
•
Insufficient operating hours of
the Ozone & Saltwater System.
•
The salt level in the pool water
is less than 2000ppm. This is
insufficient.
•
Chlorine loss due to intense
sunlight exposure.
•
The bather load has increased.
•
Clogged or dirty electrolytic cell.
•
HighUVlevelexposure.
•
Excessive calcium hardness is
present in pool water.
•
No power supply.
• RCD/GFCIhasnotreseted.
•
A power fuse has blown.
•
LED failure.
•
Increase the daily Ozone & Saltwater System
operating time. See “Operating Instructions”.
•
Check the salt level with the Test Kit. Adjust as
needed.See“Salt&PoolWaterVolumes”.
•
Add appropriate stabilizer. See “Cyanuric Acid
table”.
•
Use a pool cover when the pool is not in use and/
or when the unit is operating.
•
Increase the daily Ozone & Saltwater System
operating time. See “Operating Instructions”.
•
Remove the cell for inspection, clean it if necessary.
See “Maintenance”.
•
Cover the pool with a pool cover for 2 days
with the device running and then test the
water using the test strips.
•
If the pool is clean and clear, add stabilizer to the
water and then test the water with the device running.
•
Drainabout20to25%ofthepoolwaterand
add fresh water to decrease the calcium
hardness. Inspect the electrolytic cell for
scale buildup. Clean the electrolytic cell if
necessary.
•
Plug the cell cord firmly into the cell housing
receptacle.
•
Findouttheswitchandturnon.
•
ResettheRCD/GFCI.
•
Contact Intex Service Center.
PROBLEM CAUSE SOLUTION
IMPORTANT
If you continue to experience difficulty, please contact our Consumer Service
Department for assistance. See separate “Authorized Service Centers” sheet.
Operation is subject to the following two conditions:
(1)
this device may not cause interference, and
(2)
this device must accept any interference, including interference that may cause undesired operation
of the device.
Changes or modifications not expressly approved by the party responsible for compliance could void
the user’s authority to operate the equipment.
ThisequipmenthasbeentestedandfoundtocomplywiththelimitsforClassBdigitaldevice,
pursuanttopart15oftheFCCRules.Theselimitsaredesignedtoprovidereasonableprotection
against harmful interference in a residential installation. This equipment generates, uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or more of the following
measures:
•
Reorient or relocate the receiving antenna.
•
Increase the separation between the equipment and the receiver.
•
Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
•
Consultthedealeroranexperiencedradio/TVtechnicianforhelp.
… 20 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex ZS8110 Krystal Clear at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex ZS8110 Krystal Clear in the language / languages: English as an attachment in your email.

The manual is 3,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info