686153

Intex ZS6110 Krystal Clear Manual

8
Zoom out
Zoom in
Previous page
1/23
Next page
(328PO) MODEL ZS6110 OZONE & SALTWATER SYSTEM ENGLISH 7.5” X 10.3” PANTONE 295U 05/26/2017
328
PO
SAVE THESE INSTRUCTIONS
English
Page 8
SALT & POOL WATER VOLUMES
• Which kind of salt to use:
Use only Sodium Chloride Salts
Use only sodium chloride (NaCl) salt that is at least 99.8% pure. It is also acceptable to use
water conditioning salt pellets (the compressed forms of evaporated salt). However, it will take a
longer time for them to dissolve.
Do not use iodized or yellow (yellow prussiate of soda) colored salt.
Salt is added to the pool water and the electrolytic cell uses the salt to create chlorine. The purer
the salt the better the performance of the electrolytic cell.
• Optimum Salt Levels
The ideal salt level in the pool water is between 2500-3500 ppm (parts per million). The optimal
level is 3000 ppm.
A too low salt level will reduce the efficiency of the Ozone & Saltwater System and result in
low chlorine production. A high salt level may generate a salty taste to the pool water (this may
occur at a salt level above 3500-4000 ppm). Too high a salt level may damage the power
supply and cause corrosion to the pool metal fixtures and accessories. The Salt Table page of
this manual, shows the correct dosage of salt needed. The salt in the pool is constantly
recycled. The loss of salt is due only to pool water being physically removed from the pool.
Salt is not lost due to evaporation.
• Adding Salt
1.
Switch the filter pump on to start the water circulation.
2.
Keep the Ozone & Saltwater System turned off.
3.
Determine the amount of salt to be added (see “Salt Table”).
4.
Evenly spread the proper amount of salt around the inside perimeter of the pool.
5.
Avoid clogging the filter. Do not add salt through the skimmer.
6.
Brush the pool bottom to speed up the dissolving process. Do not allow salt to pile up on the
bottom of the pool. Run the filter pump 24 consecutive hours to thoroughly dissolve the salt.
7.
After 24 hours and if all the salt is dissolved, turn on the Ozone & Saltwater System, press
button until you hear a “beep”, code “00” flashing and set the saltwater pool system to
desired operating time (see “Operating Time Table”).
• Removing Salt
If too much salt has been added, the unit will beep and display “Code 92” (see “Alarm Codes”).
You will need to lower the salt concentration. The only way to do so, is to partially drain the pool
and refill it with fresh water. Drain and refill approximately 20% of the pool’s water until the “Code
92” disappears.
• Pool Volume Calculation
Rectangular
Length x Width x Average Depth x 7.5 Length x Width x Average Depth
Circular
Length x Width x Average Depth x 5.9 Length x Width x Average Depth x 0.79
Oval
Length x Width x Average Depth x 6.0 Length x Width x Average Depth x 0.80
Types of Pool
Gallons
(pool size in feet)
Cubic Meters
(pool size in meters)
… 8 …


Need help? Post your question in this forum.

Forumrules
1

Forum

intex-zs6110-krystal-clear

Reset search

  • How do I take the cover off to get to the motherboard?
    Submitted Submitted on 7-7-2022 at 21:39

    Reply Report abuse

  • How do I take the cover off to get to the motherboard? Submitted on 20-6-2022 at 03:33

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex ZS6110 Krystal Clear at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex ZS6110 Krystal Clear in the language / languages: English as an attachment in your email.

The manual is 2,91 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info