752295
7
Zoom out
Zoom in
Previous page
1/12
Next page
118A
SAVE THESE INSTRUCTIONS
(118IO) ULTRA FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 09/28/2017
English
Page 7
POOL SETUP (continued)
You may have purchased this pool with the Intex Krystal Clear™ filter pump. The pump has its own
separate set of installation instructions. First assemble your pool unit and then set up the filter pump.
Estimated assembly time 45-60 min. (Note the assembly time is only approximate and individual assembly
experience may vary.)
1. Liner preparation
Find a flat, level location that is free and clear of stones, branches or other sharp objects that may
puncture the pool liner or cause injury.
Open the carton containing the liner, joints, legs, etc., very carefully as this carton can be used to store
the pool during the winter months or when not in use.
Take out the ground cloth (7) and spread it over the cleared
area. Then, take out the liner (5) and spread it out over the
ground cloth, with the drain valve directed towards the
draining area. Place the drain valve away from the house.
Allow the sun to warm up the liner before inserting the
beams
(4) into the sleeve openings.
IMPORTANT: Always set up the pool unit with at least 2
persons. Do not drag the liner across the ground as
this can cause liner damage and pool leakage (see
drawing 1).
During the set-up of this pool liner, point the hose connections or openings in the direction of the electric
power source. The outer edge of the pool should be within reach of the pump’s electrical connection.
2. Frame assembly
The frame pool’s legs (2) and beams (4) fall into two groups. The smaller
diameters are the vertical legs. Both these legs and beams fit into the
T-joints
(1).
Starting at any location, but always working in the same direction, push
the horizontal beam into the sleeve (see drawing 2.1). Once the beam is
centered take one of the T- joints (1), snap the joint to one end of the
beam by aligning the hole and the spring-loaded pin. Repeat this
procedure in a circular fashion until all the beams and joints have been
connected
(see drawing 2.2).
The last joint connection may be difficult to complete, but can be
easily done by simultaneously raising this last joint and beam more
than 2 inches (5 cm), and connect the beam to the joint while
lowering these pieces to their normal position. The joint will slide
into the beam (see drawing 2.3). Make sure the last joint is fully
assembled before proceeding to assembling the legs.
1
5
2.1
2.3
12.2
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex Ultra Frame 610 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex Ultra Frame 610 in the language / languages: English as an attachment in your email.

The manual is 0,99 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex Ultra Frame 610

Intex Ultra Frame 610 User Manual - German - 12 pages

Intex Ultra Frame 610 User Manual - Dutch - 13 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info