784581
17
Zoom out
Zoom in
Previous page
1/27
Next page
346
PO
S AVE THESE INSTRUCTIONS
(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019
English
Page 17
LED CODE CHART
LED Reading CAUSE SOLUTION
E81 Transmission signal failure
Reset the RCD, restart all over again.
Place the control panel within 5 m (16 ft) of the
control base unit.
Press and hold POWER button for 5 seconds to
turn off and charge the panel again.
If problem persists, contact Intex Service Center.
E90 No water ow
Turn off and unplug the control unit.
Ensure the outlet cover grid is clean and free from
obstructions.
Clean or replace the cartridge, see Maintenance
and Storage section.
Ensure the in/outlet connections on the spa tub and
lter pump are not blocked.
Keep the spa water properly sanitized to ensure a
clean and unclogged lter cartridge.
If problem persists, contact Intex Service Center.
E94 Water temperature too low
If the ambient temperature is below 39°F (4°C), we
recommend not to use the spa.
• Turn off and unplug the control unit, add some
warm water to raise the spa water temperature
above 41°F (5°C), then press the
button to heat
up the water to the desired temperature.
If problem persists, contact Intex Service center.
E95 Water temperature too high
Turn off and unplug the control unit. When the water
has cooled down, plug the RCD and restart all over
again.
Turn the heater off, then press the lter and bubble
buttons to lower the water temperature.
If problem persists, contact Intex Service Center.
E96 System Error
Turn off and unplug the control unit. Plug the RCD
and restart all over again.
• If problem persists, contact Intex Service Center.
E97 Dry- re Protection • Contact Intex Service Center.
E99 Water temperature sensor broken Contact Intex Service Center.
END
After 72 hours of continuous
heating operation, the pump will
hibernate automatically. The rapid
heating function is disabled.
• Press the
button to re-active the lter pump.
BLANK
Control panel battery has no power
or in “Power Saving Mode” waiting
to be placed on the control base
recessed channel.
Press any button to reactivate the control panel.
Reset the RCD, restart all over again and charge
the control panel again.
Make sure the surface between the back of the
control panel and the control base recessed channel
is clean, dry and free of obstruction.
If problem persists, contact Intex Service Center.
17


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SSP-H-10 PureSpa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SSP-H-10 PureSpa in the language / languages: English as an attachment in your email.

The manual is 3.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info