784581
14
Zoom out
Zoom in
Previous page
1/27
Next page
346
PO
S AVE THESE INSTRUCTIONS
(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019
English
Page 14
SPA CONTROL PANEL
F: Heat Button
G: Celsius/Fahrenheit Toggle Button
H: Heat System Delay Timer (HSDT) Button
I: Heat System Operating Hours (HSOH) Button
OPERATION (continued)
Heat Button: Press this button to activate the heating system. Press or to set the desired
water temperature. The system will heat the spa water until the water temperature reaches the
set temperature. When the spa water temperature drops 2°F below the set temperature the
heating system will restart. When the ame icon on the display is red, the heating system is
activated. When the ame icon turns green, the water is at the set temperature. The heating
system is at rest and the ltration system will continue working nonstop. If the heating system is
activated the lter pump will start at the same time.
NOTE: To stop the ltration system while the heater is at rest mode, press the ame button
rst and then the lter button. Pressing the heat button only while the heater is at rest mode will
turn off the heating system only and the ltration system will operate for 1 more minute before it
turns off or continue with the lter pump preset operating hours.
IMPORTANT: The following conditions will lead to slow water heating.
The ambient temperature is lower than 50ºF (10ºC).
Outdoor wind speed is above 3.5-5.4 m/s (8-12 mph).
The air bubble function is activated when heating the spa water.
The spa is not properly covered with the spa cover when the water is heating.
Celsius/Fahrenheit Toggle button: The temperature can be displayed in either Fahrenheit or
Celsius. The system’s default is Celsius.
NOTE: The default temperature is 68°F (20°C). Temperature adjustment ranges from 50°F
(10°C ) to 104°F(40°C).
CAUTION: NEVER use the spa if indicated water temperature is more than 104ºF(40°C).
Heat System Delay Timer (HSDT) Button: Press this button and then press or to set
the heating system starting time timer, from 001 to 120 hours. The icon will ash red for a few
seconds and then stays red. Once the countdown timer reached 000, the heating system will
start operating. Repeat previous steps to reprogram this function. Set the Heat System Delay
Timer time to 000 to deactivate this function. Press the HSDT button twice any time to re-adjust
the preset hours.
Heat System Operating Hours (HSOH) Button: Press this button and then press or to
set the heating system operating hours from 000 to 048 hours. The icon will ash red for a few
seconds and then stays red. The heating system will operate for the amount of preset hours
only regardless if the preset spa water temperature is reached or not. The information shown on
the LED display alternates between the remaining operating hours and the water temperature,
provided the HSDT function is not set. Repeat previous steps to reprogram this function. Set
the Heat System Operating Hours to 000 to deactivate this function. Press the HSOH button
twice any time to re-adjust the preset hours.
HG
F
I
14


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SSP-H-10 PureSpa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SSP-H-10 PureSpa in the language / languages: English as an attachment in your email.

The manual is 3.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info