784581

Intex SSP-H-10 PureSpa Manual

4
Zoom out
Zoom in
Previous page
1/27
Next page
346
PO
S AVE THESE INSTRUCTIONS
(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019
English
Page 4
WARNING
j) Exit immediately if uncomfortable, dizzy, or sleepy. Spa heat can cause hyperthermia and unconsciousness. The use of alcohol, drugs, or
medication can greatly increase the risk of fatal hyperthermia. The causes, symptoms, and effects of hyperthermia may be described as
follows:
Hyperthermia occurs when the internal temperature of the body reaches a level several degrees above the normal body temperature of
98.6°F (37°C). The symptoms of hyperthermia include an increase in the internal temperature of the body, dizziness, lethargy, drowsiness,
and fainting. The effects of hyperthermia include failure to perceive heat; failure to recognize the need to exit spa or hot tub; unawareness
of impending hazard; fetal damage in pregnant women; physical inability to exit the spa or hot tub; and unconsciousness resulting in the
danger of drowning.
• People with infectious diseases should not use a spa or hot tub.
• To avoid injury exercise care when entering or existing the spa or hot tub.
• Always add chemicals to water, never add water to chemicals. Adding water to chemicals may cause strong fumes or violent reactions and
hazardous chemical spray.
• Never jump or dive into a spa or any shallow body of water.
• Assembly and disassembly by adults only.
• Always unplug this product from the electrical outlet before removing, cleaning, servicing or making any adjustment to the product.
• The plug must be accessible after product is installed.
• Do not bury the electrical cord. Locate the cord where it will not be damaged by lawn mowers, hedge trimmers and other equipment.
• If the supply cord is damaged, it must be replaced by a qualifi ed electrician in order to avoid a hazard. Use only identical replacement parts
when servicing.
• To reduce the risk of electric shock and fi re, do not use extension cords, timers, plug adaptors or converter plugs to connect unit to
electrical supply; provide a properly located outlet.
• Do not attempt to plug in or unplug this product while standing in water or when your hands are wet.
• Do not leave the spa empty for extended period of time. Do not expose the spa to direct sunlight for extended period of time.
• Provide adequate drainage system around the spa to deal with overfl ow water and splashes.
• Do not allow the water in the spa to freeze. Do not turn on the spa when the water is frozen.
• Do not use the spa if damaged in delivery and/or malfunctioning in any fashion. Contact the Intex service center for further direction.
• Never pour water with a temperature higher than 104°F (40°C) into the spa directly.
• Keep all pets away from spa to avoid any damage.
• Do not add bath oil or bath salt to the spa water.
• Avoid drowning risk. Keep children away. Children or objects cannot be seen under cover.
• Remove cover completely before entry of bathers – entrapment possible.
• Stay off cover – will not support weight.
• Non-secured or improperly secured covers are a hazard.
• Follow these rules to avoid drowning, or other serious injury.
CAUTION
• Maintain water chemistry in accordance with manufacturer’s instructions.
• This product is provided with a GFCI/RCD located at the end of the power cord. The GFCI/RCD must be
tested before each use. Do not use the spa if the GFCI/RCD does not function properly. Disconnect the
power cord until the fault has been identifi ed and corrected. Contact a qualifi ed electrician to correct the
fault. Do not bypass the GFCI/RCD. There are no serviceable parts inside the GFCI/RCD. Opening the
GFCI/RCD will void the warranty.
1. Plug the power cord into a grounded electrical socket.
2. Press the
RESET button on the GFCI/RCD.
3. Turn on the spa electrical equipment.
4. Press the
TEST button on the GFCI/RCD. The GFCI/RCD indicator
should turn off and the electrical equipment should shut off. If the
GFCI/RCD indicator does not turn off, and the electrical equipment
does not shut off, the GFCI/RCD is faulty. Do not use the spa.
Contact a qualifi ed electrician to correct the fault.
5. Press the
RESET button on the GFCI/RCD. The indicator on
the GFCI/RCD should turn on. If the GFCI/RCD indicator does
not turn on, the GFCI/RCD is faulty. Do not use the spa.
Contact a qualifi ed electrician immediately to correct the fault.
WARNING
TEST
RESET
RESET
TEST
TEST
RESET
RESET
TEST
TEST
… 4 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SSP-H-10 PureSpa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SSP-H-10 PureSpa in the language / languages: English as an attachment in your email.

The manual is 3.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info