686577
15
Zoom out
Zoom in
Previous page
1/22
Next page
193
GS
SAVE THESE INSTRUCTIONS
(193GS) MODEL SF90220RC SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/27/2015
English
Page 15
Initial startup and operation:
Before operating, be sure that:
All the hoses have been connected and tightened securely, and correct amount of filter sand
have been loaded.
The entire system is connected to a grounding type receptacle protected by a ground-fault
circuit interrupter (GFCI) or residual current device (RCD).
OPERATING INSTRUCTIONS (continued)
CAUTION
The filter control valve has a closed position. The pump should never be
on when the valve is in the closed position. If the pump is operated with
the valve closed, explosive situation could exist.
1. Turn both plunger valve handles fully counter-clockwise until
they stop.This opens the valves to allow water to flow into
the sand filter pump.
2. Release air from the system - Ensure the drain/waste outlet
on the 6-way valve is not covered and directed to a proper
draining receptacle, and the pump is off. Turn the 6-way
valve to the “N” position and unscrew the air release valve
(36) from the motor housing (see drawing 29). When water
starts flowing out of the air release valve hole, close the air
release valve back.
3. BACKWASH - Ensure the pump is off, depress the 6-way
valve and turn it to the “BACKWASH” position (see
drawings 24 & 30).
IMPORTANT: To prevent damage to the 6-way valve,
always depress the valve handle before turning. Always
switch off pump before changing the 6-way valve
position.
4. Switch on the pump (see drawing 31). Water is circulating
backward through the sand media and to waste/drain outlet.
Backwash until a clear flow of water is observed in the waste/
drain outlet or through the transparent outlet adaptor.
NOTE: The initial backwash of the filter is recommended to
remove any impurities or fine sand particles in the sand
media.
30
1
2
N
29
36
31
OFF
ON
TIMER
26 27 28
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SF90220RC at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SF90220RC in the language / languages: English as an attachment in your email.

The manual is 4,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex SF90220RC

Intex SF90220RC User Manual - German - 21 pages

Intex SF90220RC User Manual - Dutch - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info