686592
21
Zoom out
Zoom in
Previous page
1/23
Next page
342
GS
SAVE THESE INSTRUCTIONS
(342GS) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 08/22/2019
English
Page 21
TROUBLESHOOTING GUIDE
Line cord must be plugged into a 3 wire outlet
that is protected by a Class A Ground Fault
Circuit Interrupter, or RCD.
Reset circuit breaker. If circuit breaker trips
repeatedly, your electrical system may have a
defect. Turn off circuit breaker and call an
electrician to correct the problem.
Let the motor cool down and restart again.
Adjust the chlorine and pH level. Consult your local
swimming pool supply stores.
Load with filter sand, see “sand loading instructions”.
Set valve to “FILTER” position.
Operate the filter for longer periods.
Clean the strainer screen at the inlet.
Clear any obstructions in the intake hose by discharging it
inside pool wall.
Tighten hose nuts, check hoses for damage, check pool
water level.
Clean the pre-filtering basket more often.
• Backwash filter.
Install the nozzle at the upper position of the pool inlet, and
the strainer at the lower position of the pool outlet.
Remove about 1” of sand if necessary.
Remove any pool vacuuming device attached to the
system line.
Make sure the inlet threaded air connector is connected to
the pool inlet upper hole.
Fill pool to correct water level.
Clean strainer screens at pool inlet.
Tighten hose nuts, check hose for damage.
Contact Intex service center.
Remove 6-way valve cover and ensure the o-ring is in place.
Clean sand tank o-ring with garden hose water.
• Tighten securely.
Contact Intex service center.
Tighten/reinstall hose nut.
Ensure o-ring/L-shape o-ring is in place and
not damaged.
Turn off the pump and restart 5 minutes later.
Re-set the timer.
Contact Intex service center.
Clear any obstructions in the intake by
unscrewing it from the 6-way valve.
Contact Intex service center.
Use only No. 20 silica sand with particle size
range 0.45 to 0.85 mm (0.018 to 0.033 inches)
and a Uniformity Coefficient less than 1.75.
• Change sand.
Tighten or reinstall plunger valve.
Tighten air jet valve and make sure it’s
facing up.
Turn pump ON and run for few seconds, then
turn OFF, repeat 3 times.
Remove air jet valve, flush dirt out with water
and replace valve back.
Replace a new air jet valve.
FILTER MOTOR FAILS
TO START
FILTER DOESN’T
CLEAN POOL
FILTER DOESN’T PUMP
WATER OR FLOW IS
VERY SLOW
PUMP DOESN’T
WORK
6-WAY VALVE/COVER
LEAKING
HOSE LEAKING
TIMER IS INACCURATE
OR TIMER CAN'T BE SET
PRESSURE GAUGE
DOESN’T WORK
SAND IS FLOWING
BACK INTO THE POOL
INLET THREADED
AIR CONNECTOR/AIR
JET VALVE LEAKING
The motor is not plugged in.
The GFCI/RCD circuit breaker
is tripped.
Motor too hot and overload
protection is shut off.
Improper chlorine or pH levels.
No filtering media in tank.
Wrong 6-way valve setting position.
Excessively dirty pool.
The strainer screen is restricting
the water flow.
Clogged inlet or discharge.
An air leak on the intake line.
Excessively dirty pool.
Sand media clogged with dirt.
Nozzle and strainer connections
are reversed.
Crusting or caking on the filtering
sand surface.
Pool vacuuming device attached
to the system.
Inlet threaded air connector
connected to the wrong hole on
the liner.
Low water level.
Strainer screen clogged up.
An air leak on the intake hose.
Faulty motor or the impeller is jammed.
Sand tank o-ring missing.
Sand tank o-ring dirty.
Flange clamp not tight.
6-way valve damage.
Hose nut not securely tight.
Hose connection fitting
o-ring/L-shape o-ring missing.
Possible inner timer defective.
Clogged inlet of the pressure
gauge.
Pressure gauge damage.
Sand is too small.
Sand bed is calcified.
Plunger valve not well-fitted.
Air jet valve is not tight and
facing up.
Air jet valve internal seal blocked.
Air jet valve internal seal dirty.
Air jet valve broken.
TROUBLE CAUSE SOLUTION
21


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SF80220RC-2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SF80220RC-2 in the language / languages: English as an attachment in your email.

The manual is 6,17 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex SF80220RC-2

Intex SF80220RC-2 User Manual - German - 23 pages

Intex SF80220RC-2 User Manual - Dutch - 24 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info