686570
15
Zoom out
Zoom in
Previous page
1/23
Next page
195A
SAVE THESE INSTRUCTIONS
(195IO) SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 07/03/2015
English
Page 15
Initial startup and operation:
Before operating, be sure that:
All the hoses have been connected and tightened securely, and correct amount of filter sand
have been loaded.
The entire system is connected to a grounding type receptacle protected by a ground-fault
circuit interrupter (GFCI) or residual current device (RCD).
OPERATING INSTRUCTIONS (continued)
CAUTION
The filter control valve has a closed position. The pump should
never be on when the valve is in the closed position. If the pump is
operated with the valve closed, explosive situation could exist.
1.
Turn both plunger valve handles fully counter-clockwise until they stop. This opens the valves
to allow water to flow into the sand filter pump. With water flowing into sand filter pump, the
water pressure will allow the air trapped inside to escape from the air release valves
(19).
When all the air has escaped water will flow out of the valves
(19).
When this occurs gently
finger tighten the valves
(19)
in a clockwise direction.
IMPORTANT: To prevent air lock, open the lower plunger valve (connected inlet hose)
first and then the upper plunger valve (connected outlet hose). Open the air release
valves, wait until water starts to flow out of the air release valves, close air release
valves.
2.
Ensure the drain/waste outlet on the 6-way valve is not covered and directed to a proper
draining receptacle.
3.
BACKWASH
- Ensure the pump is off, depress the 6-way
valve and turn it to the “
BACKWASH
” position
(see
drawings 24 & 29)
.
IMPORTANT: To prevent damage to the 6-way valve,
always depress the valve handle before turning.
Always switch off pump before changing the 6-way
valve position.
4.
Switch on the pump
(see drawing 30)
. Water is circulating
backward through the sand media and to waste/drain outlet.
Backwash until a clear flow of water is observed in the
waste/drain outlet or through the drain sediment window.
NOTE:
The initial backwash of the filter is recommended to
remove any impurities or fine sand particles in the sand
media.
R
E
T
LI
F
E
S
NI
R
ER
H
S
AWK
CA
B
ESO
L
C
ETSAW
26
R
E
T
LIF
ESN
I
R
E
TA
L
U
C
R
I
CE
R
HS
A
W
K
C
A
B
E
S
O
L
C
27
R
E
TLI
F
ETALUC
R
ICER
H
S
A
WK
CA
B
ES
O
LC
ETSAW
28
29
1
2
30
TIMER
OFF
ON
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SF70220 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SF70220 in the language / languages: English as an attachment in your email.

The manual is 5,47 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info