752336
18
Zoom out
Zoom in
Previous page
1/20
Next page
128
GS
SAVE THESE INSTRUCTIONS Page 18
(128GS) MODEL SF20220R SAND FILTER PUMP ENGLISH 7.5” X 10.3” PANTONE 295U 10/28/2011
TROUBLESHOOTING GUIDE
TTRROOUUBBLLEESSHHOOOOTTIINNGG GGUUIIDDEE
English
Line cord must be plugged into a 3
wire outlet that is protected by a Class
A Ground Fault Circuit Interrupter, or
RCD.
Reset circuit breaker. If circuit breaker
trips repeatedly, your electrical system
may have a defect. Turn off circuit
breaker and call an electrician to
correct the problem.
Let the motor cool down and restart again.
Adjust
the
chlorine and pH level. Consult
your local pond supply stores.
Load with filter sand, see “sand loading
instructions”.
Set valve to “ FILTER” position.
Operate
the
filter for longer periods.
Clean
the
strainer screen at the inlet.
Clean the pre-filtering basket more often.
Backwash filter.
Remove about 1” of sand if necessary.
Remove any pond vacuuming device
attached to the system line.
Fill pond to correct water level.
Clean strainer screens at pond inlet.
Contact Intex service center.
Remove 6-way valve cover and ensure the
o-ring is in place.
Clean sand tank o-ring with garden hose water.
Tighten the clamp with wrench supplied.
Contact Intex service center.
Tighten/reinstall hose nut.
Ensure o-ring/L-shape o-ring is in place
and not damaged.
Turn off the pump and restart 5 minutes
later.
Re-set the timer.
Contact Intex service center.
Clear any obstructions in the intake by
unscrewing it from the 6-way valve.
Contact Intex service center.
Use only No. 20 silica sand with particle
size range 0.45 to 0.85 mm (0.018
to 0.033 inches) and a Uniformity
Coefficient less than 1.75.
Change sand.
FILTER MOTOR
FAILS TO START
FILTER DOESN’T
CLEAN POND
FILTER DOESN’T
PUMP WATER OR
FLOW IS VERY
SLOW
PUMP DOESN’T
WORK
6-WAY
VALVE/COVER
LEAKING
HOSE LEAKING
TIMER IS
INACCURATE OR
TIMER CAN'T BE
SET
PRESSURE GAUGE
DOESN’T WORK
SAND IS FLOWING
BACK INTO THE
POND
The motor is not plugged in.
The fuse box needs checking.
The GFCI/RCD circuit breaker
is tripped.
Motor too hot and overload
protection is shut off.
Improper chlorine or pH
levels.
No filtering media in tank.
Wrong 6-way valve setting
position.
Excessively dirty pond.
The strainer screen is
restricting the water flow.
Clogged inlet or discharge.
An air leak on the intake line.
Excessively dirty pond.
Sand media clogged with dirt.
Nozzle and strainer
connections are reversed.
Crusting or caking on the
filtering sand surface.
Pond vacuuming device
attached to the system.
Low water level.
Strainer screen clogged up.
Faulty motor or the impeller
is jammed.
Sand tank o-ring missing.
Sand tank o-ring dirty.
Flange clamp not tight.
6-way valve damage.
Hose nut not securely tight.
Hose connection fitting
o-ring/L-shape o-ring missing.
Possible inner timer
defective.
Clogged inlet of the pressure
gauge.
Pressure gauge damage.
Sand is too small.
Sand bed is calcified.
TROUBLE CAUSE SOLUTION
IMPORTANT
If you continue to experience difficulty, please contact our Consumer
Service Department for assistance. See back cover for contact information.
18


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SF20220 Pump at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SF20220 Pump in the language / languages: English as an attachment in your email.

The manual is 4,73 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex SF20220 Pump

Intex SF20220 Pump User Manual - German - 27 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info