752503
11
Zoom out
Zoom in
Previous page
1/18
Next page
120A
SAVE THESE INSTRUCTIONS
(120IO) SEQUOIA SPIRIT™ WOOD-GRAIN FRAME POOL ENGLISH 7.5” X 10.3” PANTONE 295U 06/16/2014
English
Page 11
POOL ENCLOSURE SETUP
Once the pool has been filled with water, and it has been confirmed that it is completely level and that all
vertical legs are positioned in the middle of each patio block, proceed with the assembly of the pool
enclosure.
1. Top clamp installation
Fasten a top clamp (16) to the T-joint of the pool frame from the underneath. Ensure the two bolts on
top clamp are facing upward. Repeat the procedure until all the top clamps are fastened to the T joints
of the pool frame (see drawings 8.1 & 8.2).
2. Bottom cap and bottom rail installation
Place a bottom cap (25) on the ground and align it with the leg cap. Ensure that the threaded side hole
in the bottom cap is facing outward. Place all bottom caps in position.
Starting at any location, but always working in the same direction, connect a bottom rail (24) in between
two bottom caps (25). Ensure the pre-drilled holes on the bottom rail hook through the knobs on the
bottom cap. Repeat this procedure in a circular fashion until all the bottom rails and bottom caps have
been connected. Adjust the distance of the bottom cap to the leg cap by estimating that the support
post
(17) will stand vertical after it is installed (see drawings 9.1 & 9.2).
3. Support post installation
Remove the cardboard inserts from the both slides of each support post.
Insert the support post (17) into the bottom cap (25). Lift up the support post slightly to let the slot on
the upper end of the support post hook onto the ridge at the top clamp. Push downward to ensure the
support post is connected firmly with the top clamp and inserted in the bottom cap (see drawings 10.1,
10.2 & 10.3).
Repeat these procedures until all the support posts are joined to the top clamps and bottom caps (see
drawing 10.4).
8.1 8.2
9.1 9.2
10.1 10.2
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex Sequoia Spirit at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex Sequoia Spirit in the language / languages: English as an attachment in your email.

The manual is 3,01 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex Sequoia Spirit

Intex Sequoia Spirit User Manual - German - 18 pages

Intex Sequoia Spirit User Manual - Dutch - 25 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info