784579
12
Zoom out
Zoom in
Previous page
1/27
Next page
346
PO
S AVE THESE INSTRUCTIONS
(346PO) SPA ENGLISH 7.5” X 10.3” PANTONE 295U 08/10/2019
English
Page 12
SET UP (continued)
Spa Control Unit Installation
1. Connect the spa control unit to the spa tub (see drawing 10). Hand-tighten the connectors securely. Do not
use tools to tighten.
NOTE: Never attach external accessories not supplied with the kit to the spa tub or control base unit, as
this will void the warranty.
2. Replace the control base side covers (4) (see drawing 11).
CAUTION: Do not sit, lean, cover or place any objects over the spa control unit.
3. Attach the two lter cartridge housing assemblies to the two outlet
grids on the inside of the spa (lower position, marked “C”). In ate
the spa tub rst before installing lter pump ttings.
ATTENTION! In order to comply with the requirements of the
Virginia Grahame Baker Act, suction outlets cannot be covered
while the spa is in use. The Act was intended to address high
suction/volume circulation systems but does not exclude low
volume systems as used on this spa. Accordingly, remove the lter
cartridge assemblies and any other spa cleaning attachment from
the spa outlets before spa usage (see drawing 12).
Re-attach them after usage for water ltration and cleaning.
4. Before lling with water ensure the bottom drain valve caps are
securely closed on the inside and outside.
5. Fill the spa tub with freshwater to a level between MIN and MAX
marked on the inside of the spa wall. Do not over ll the spa.
Never move the spa tub with water inside and/or with the control
base attached to the spa as the spa or control base may be damaged.
WARNING: Never pour water with a temperature higher than
104°F(40°C) into the spa directly. It is recommended to ll the spa tub with lukewarm water for quick
heating and energy saving.
6. Place the spa cover and spa air bladder (pre-installed in spa cover)
over the spa tub, and make sure the spa cover buckles are locked using the key provided after pulling the
buckled straps tight.
IMPORTANT: Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never
use a damaged spa cover.
7. Ensure the spa is plugged into a electrical socket and press the button to turn on the control panel
buttons rst. Press the button on the control panel to activate the heater, see “Spa Control Panel”
operation section.
11
10
12
C
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex SB-HW10 PureSpa at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex SB-HW10 PureSpa in the language / languages: English as an attachment in your email.

The manual is 3.12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info