686582
12
Zoom out
Zoom in
Previous page
1/29
Next page
299
NLA
S AVE THESE INSTRUCTIONS
(299NL) SPA (JET + BUBBLE) ENGLISH 7.5” X 10.3” PANTONE 295U 05/10/2017
English
Page 12
SET UP (continued)
De ation
For Spa Tub Wall:
1. Unscrew the cap to reveal the stem, push the stem in
and turn 90 degree right to secure it in the down
position
(see drawing 8).
2. Once the de ation is completed, push the stem in and
turn 90 degree left to return it to the in ation position.
3. Replace the cap back.
For Cover Air Bladder:
1. Pull valve cap out and squeeze the valve at its base
until de ated.
2. Close and recess the valve back.
Spa Control Unit Installation
1. Connect the spa control unit to the spa tub (see drawing 9). Hand-tighten the connectors securely.
Do not use tools to tighten.
CAUTION: Do not sit, lean, cover or place any objects over the spa control unit.
2. Attach the lter cartridge housing assembly to the inside of the spa tub outlet grid (marked “B”) (see
drawing 10). In ate the spa tub rst before installing lter pump ttings.
3. Before lling with water ensure the bottom drain valve caps are securely closed on the inside and outside.
4. Fill the spa tub with freshwater to a level between MIN and MAX marked on the inside of the spa wall. Do
not over ll the spa. Never move the spa tub with water inside and/or with the control base attached to the
spa as the spa or control base may be damaged.
WARNING: Never pour water with a temperature higher than 40°C (104°F) into the spa
directly. It is recommended to ll the spa tub with lukewarm water for quick heating and
energy saving.
5. Place the spa cover and spa air bladder (pre-installed in spa cover) over the spa tub, and make sure the
spa cover buckles are locked using the key provided after pulling the buckled straps tight.
IMPORTANT: Inspect the spa cover regularly for leak, premature wear and tear or deterioration. Never
use a damaged spa cover.
6. Ensure the spa is plugged into an electrical socket and press the button to turn on the control unit
panel buttons rst. Press the button on the control panel to activate the heater, see “Spa Control Unit
Panel” operation section.
IMPORTANT: The following conditions will lead to slow water heating:
The ambient temperature is lower than 50ºF (10ºC).
Outdoor wind speed is above 8-12 mph (3.5-5.4 m/s).
The jet function is activated when heating the spa water.
The spa is not properly covered with the spa cover when the water is heating.
8
10
B
B
C
A
A
C
B
9
12


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Intex PureSpa SJB-HS-30-1G at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Intex PureSpa SJB-HS-30-1G in the language / languages: English as an attachment in your email.

The manual is 2,67 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Intex PureSpa SJB-HS-30-1G

Intex PureSpa SJB-HS-30-1G User Manual - German - 29 pages

Intex PureSpa SJB-HS-30-1G User Manual - Dutch - 30 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info